Zune Flash 2Nd Generation Lcd Display Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 - 20 minutes

Sections

Back Cover
5 steps
Face Plate
7 steps
LCD Display
2 steps

Flags

Inconsistent Images

Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

BackZune Flash 2nd Generation
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Back Cover

Prior to disassembly, verify the hold switch is engaged to ensure the device will not turn on during the procedure.
If the device turns on while it is being disassembled it could cause irreversible damage to the device.
PICS MAKE NO SENSE.

Prior to disassembly, verify the hold switch is engaged to ensure the device will not turn on during the procedure.

If the device turns on while it is being disassembled it could cause irreversible damage to the device.

PICS MAKE NO SENSE.

1024

Step 2

Remove the top metal clip by inserting a Zune opening tool in between the faceplate and back cover and pulling gently back as shown in the images.
You should hear a ‘click’ as the clip detaches from the device.

Remove the top metal clip by inserting a Zune opening tool in between the faceplate and back cover and pulling gently back as shown in the images.

You should hear a ‘click’ as the clip detaches from the device.

Step 3

Remove the two screws shown using a small Tri-Wing screwdriver.
You will need to use a very small Tri-Wing screwdriver to ensure that you do not strip the screws.

Remove the two screws shown using a small Tri-Wing screwdriver.

You will need to use a very small Tri-Wing screwdriver to ensure that you do not strip the screws.

Step 4

Insert the Zune opening tool between the faceplate and the back cover, starting from the top and slowly work your way around the device.

Insert the Zune opening tool between the faceplate and the back cover, starting from the top and slowly work your way around the device.

Step 5

Work your way around the Zune until the back cover comes free. Remove the back plate and set it aside.

Work your way around the Zune until the back cover comes free. Remove the back plate and set it aside.

Step 6

              Face Plate

Remove the three screws (5.5mm by 3mm) from the backside of the Zune using a small Tri-Wing screwdriver.
Be sure to put this set of screws aside since they are a different size than any other screws in the device.

Remove the three screws (5.5mm by 3mm) from the backside of the Zune using a small Tri-Wing screwdriver.

Be sure to put this set of screws aside since they are a different size than any other screws in the device.

Step 7

Use your finger or a Zune opening tool to pry back the two clear flaps.
Next lift the communications board that was being held down by the clear flaps.
Be careful not to accidentally detach the slim ribbon that connects between the communications board and the device.

Use your finger or a Zune opening tool to pry back the two clear flaps.

Next lift the communications board that was being held down by the clear flaps.

Be careful not to accidentally detach the slim ribbon that connects between the communications board and the device.

Step 8

Disconnect the ribbon with the plastic opening tool by flipping up the black plastic flap where the ribbon connects to the memory board.
Carefully pull the ribbon out of the memory board, ensuring that the black plastic flap is up before removal to avoid the ripping the ribbon.

Disconnect the ribbon with the plastic opening tool by flipping up the black plastic flap where the ribbon connects to the memory board.

Carefully pull the ribbon out of the memory board, ensuring that the black plastic flap is up before removal to avoid the ripping the ribbon.

Step 9

Remove the battery by prying the battery off from the bottom with a Zune opening tool.
There is an adhesive between the battery and the device, therefore use a metal spudger to finish detaching the battery.
Be sure not to puncture the battery in any way when using the metal spudger.

Remove the battery by prying the battery off from the bottom with a Zune opening tool.

There is an adhesive between the battery and the device, therefore use a metal spudger to finish detaching the battery.

Be sure not to puncture the battery in any way when using the metal spudger.

Step 10

Remove the single screw under the battery using a small Tri-Wing screwdriver.

Remove the single screw under the battery using a small Tri-Wing screwdriver.

Step 11

Disconnect the faceplate from the device by depressing the two tabs located near the middle of each of the sides using a metal spudger.
This will disconnect the last circuit board in the device from the center frame.

Disconnect the faceplate from the device by depressing the two tabs located near the middle of each of the sides using a metal spudger.

This will disconnect the last circuit board in the device from the center frame.

Step 12

Remove the faceplate by using a metal spudger to separate it from the remaining components.

Remove the faceplate by using a metal spudger to separate it from the remaining components.

Step 13

              LCD Display

Release the LCD connector ribbon by flipping up the black switch. This will disconnect the LCD from the device.
At this point the LCD screen should be easily separable from the device.

Release the LCD connector ribbon by flipping up the black switch. This will disconnect the LCD from the device.

At this point the LCD screen should be easily separable from the device.

Step 14

The LCD ribbon is adhered to the memory board with a strip of glue.
It’s safest to flip the display over before removing the ribbon, as shown in the first image.
To avoid damage, remove the LCD by pulling slowly and carefully on the ribbon, directly away from the memory board.

The LCD ribbon is adhered to the memory board with a strip of glue.

It’s safest to flip the display over before removing the ribbon, as shown in the first image.

To avoid damage, remove the LCD by pulling slowly and carefully on the ribbon, directly away from the memory board.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 6 other contributors

                    ybahman

Member since: 11/01/2009

136 Reputation

                                      4 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Cal Poly, Team 9-20, Regan Fall 2009                        

                                                  Member of Cal Poly, Team 9-20, Regan Fall 2009 



                    CPSU-REGAN-F09S9G20                     


                                            5 Members                     


                                            7 Guides authored

Inconsistent Images#

Needs Better Images#

Introduction#

What you need#

Team#

Inconsistent Images

Needs Better Images

Introduction

What you need

Team