Difficulty
Easy
Steps
12
Time Required
3 - 6 minutes
Sections
2
- Back Panel Assembly
- 8 steps
- Power Button
- 4 steps
Flags
0
BackZTE ZMax Pro
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Panel Assembly
- Flip the phone over so that the back panel of the phone is facing up.
- Wedge the plastic opening tool between the black outer panel and the silver side panel.
- Push down on the plastic opening tool to separate the back panel from the rest of the phone.
- Continue to do this around all sides of the phone until the back panel has popped all the way off.
- Removing the back panel may make loud popping noises which is normal.
Flip the phone over so that the back panel of the phone is facing up.
Wedge the plastic opening tool between the black outer panel and the silver side panel.
Push down on the plastic opening tool to separate the back panel from the rest of the phone.
Continue to do this around all sides of the phone until the back panel has popped all the way off.
Removing the back panel may make loud popping noises which is normal.
1024
Step 2
- Using your fingers, slide the SIM card all the way out of the phone.
Using your fingers, slide the SIM card all the way out of the phone.
Step 3
- Remove the yellow Kapton tape by using the tweezers to peel it up and away from the device.
Remove the yellow Kapton tape by using the tweezers to peel it up and away from the device.
Step 4
- Using the Phillips #00 screwdriver, remove the two 3.0 mm screws located near the top of the phone, next to the rear camera.
Using the Phillips #00 screwdriver, remove the two 3.0 mm screws located near the top of the phone, next to the rear camera.
Step 5
- Remove the fingerprint sensor flex cable, using the plastic opening tool to lift it out.
Remove the fingerprint sensor flex cable, using the plastic opening tool to lift it out.
Step 6
- Using the tweezers, peel back the yellow Kapton tape located on the right side of the phone.
Using the tweezers, peel back the yellow Kapton tape located on the right side of the phone.
Step 7
- Using the Phillips #00 screwdriver, remove the 15, 3.0 mm rear panel screws located around the perimeter of the phone.
Using the Phillips #00 screwdriver, remove the 15, 3.0 mm rear panel screws located around the perimeter of the phone.
Step 8
- Flip the phone over so that the screen is facing up.
- Wedge the plastic opening tool between the screen and the rear panel.
- Push up on the opening tool to separate the panel from the phone.
- Continue to do this around the entire phone until the rear panel is no longer connected to the device.
- The rear case and screen are fastened tightly to each other. It might help to use the picks as wedges to keep the case and screen separated as you run the opening tool along the edges.
Flip the phone over so that the screen is facing up.
Wedge the plastic opening tool between the screen and the rear panel.
Push up on the opening tool to separate the panel from the phone.
Continue to do this around the entire phone until the rear panel is no longer connected to the device.
The rear case and screen are fastened tightly to each other. It might help to use the picks as wedges to keep the case and screen separated as you run the opening tool along the edges.
Step 9
Power Button
- Use the plastic opening tool to remove the lower left connector on the motherboard.
Use the plastic opening tool to remove the lower left connector on the motherboard.
Step 10
- Use tweezers to pull back on the power button.
Use tweezers to pull back on the power button.
Step 11
- Use the tweezers to pull back on the volume buttons.
Use the tweezers to pull back on the volume buttons.
Step 12
- Use the tweezers to pull back on the cable connecting the power and volume button until it is removed.
Use the tweezers to pull back on the cable connecting the power and volume button until it is removed.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
5 other people completed this guide.
Author
with 3 other contributors
Nicholas Leacox
Member since: 04/18/2018
1,721 Reputation
7 Guides authored
Badges:
13
+10 more badges
Team
Cal Poly, Team S17-G3, Livingston Spring 2018
Member of Cal Poly, Team S17-G3, Livingston Spring 2018
CPSU-LIVINGSTON-S18S17G3
4 Members
16 Guides authored
Manny Carreon - Feb 4, 2019
Reply
Hpw much to repair ()