Zte Zmax Pro Back Panel Assembly Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          1 - 5 minutes

Sections

Back Panel Assembly
8 steps

Flags

BackZTE ZMax Pro
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Back Panel Assembly

Flip the phone over so that the back panel of the phone is facing up.
Wedge the plastic opening tool between the black outer panel and the silver side panel.
Push down on the plastic opening tool to separate the back panel from the rest of the phone.
Continue to do this around all sides of the phone until the back panel has popped all the way off.
Removing the back panel may make loud popping noises which is normal.

Flip the phone over so that the back panel of the phone is facing up.

Wedge the plastic opening tool between the black outer panel and the silver side panel.

Push down on the plastic opening tool to separate the back panel from the rest of the phone.

Continue to do this around all sides of the phone until the back panel has popped all the way off.

Removing the back panel may make loud popping noises which is normal.

1024

Step 2

Using your fingers, slide the SIM card all the way out of the phone.

Using your fingers, slide the SIM card all the way out of the phone.

Step 3

Remove the yellow Kapton tape by using the tweezers to peel it up and away from the device.

Remove the yellow Kapton tape by using the tweezers to peel it up and away from the device.

Step 4

Using the Phillips #00 screwdriver, remove the two 3.0 mm screws located near the top of the phone, next to the rear camera.

Using the Phillips #00 screwdriver, remove the two 3.0 mm screws located near the top of the phone, next to the rear camera.

Step 5

Remove the fingerprint sensor flex cable, using the plastic opening tool to lift it out.

Remove the fingerprint sensor flex cable, using the plastic opening tool to lift it out.

Step 6

Using the tweezers, peel back the yellow Kapton tape located on the right side of the phone.

Using the tweezers, peel back the yellow Kapton tape located on the right side of the phone.

Step 7

Using the Phillips #00 screwdriver, remove the 15, 3.0 mm rear panel screws located around the perimeter of the phone.

Using the Phillips #00 screwdriver, remove the 15, 3.0 mm rear panel screws located around the perimeter of the phone.

Step 8

Flip the phone over so that the screen is facing up.
Wedge the plastic opening tool between the screen and the rear panel.
Push up on the opening tool to separate the panel from the phone.
Continue to do this around the entire phone until the rear panel is no longer connected to the device.
The rear case and screen are fastened tightly to each other. It might help to use the picks as wedges to keep the case and screen separated as you run the opening tool along the edges.

Flip the phone over so that the screen is facing up.

Wedge the plastic opening tool between the screen and the rear panel.

Push up on the opening tool to separate the panel from the phone.

Continue to do this around the entire phone until the rear panel is no longer connected to the device.

The rear case and screen are fastened tightly to each other. It might help to use the picks as wedges to keep the case and screen separated as you run the opening tool along the edges.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      5 other people completed this guide.

Author

                                      with 5 other contributors

                    Mihir Deshmukh

Member since: 04/18/2018

405 Reputation

                                      1 Guide authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       Cal Poly, Team S17-G3, Livingston Spring 2018                        

                                                  Member of Cal Poly, Team S17-G3, Livingston Spring 2018 



                    CPSU-LIVINGSTON-S18S17G3                     


                                            4 Members                     


                                            16 Guides authored

Solomon Martinez - Nov 23, 2018

When I tried this at step 8 the screen peeled off instead of the top cover. Ruined my phone.

Introduction#

What you need#

Team#

Introduction

What you need

Team