Zte Telstra T95 Front Rear Facing Camera Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          45 minutes - 1 hour

Sections

Battery
2 steps
SIM Card
3 steps
Keypad
3 steps
Front/Rear Facing Camera
3 steps

Flags

BackZTE Telstra T95
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Remove the back cover using a plastic opening tool. Insert it into each corner starting at the upper left of the back cover and pushing out.
You may also use your finger nail if you do not have a plastic opening tool at hand.

Remove the back cover using a plastic opening tool. Insert it into each corner starting at the upper left of the back cover and pushing out.

You may also use your finger nail if you do not have a plastic opening tool at hand.

1024

Step 2

Using a plastic opening tool, push out the battery by inserting it into the small groove at the top left corner of the battery and pushing out.
The battery snaps out of place and you can remove it using your fingers.
When you are ready to insert a battery make sure the three copper teeth on the phone are aligned with the 3 copper dents on the battery.

Using a plastic opening tool, push out the battery by inserting it into the small groove at the top left corner of the battery and pushing out.

The battery snaps out of place and you can remove it using your fingers.

When you are ready to insert a battery make sure the three copper teeth on the phone are aligned with the 3 copper dents on the battery.

Step 3

              SIM Card

Step 4

Using your a plastic opening tool, push out the battery by inserting it into the small groove at the top left corner of the battery and pushing out.
The battery snaps out of place and you can remove it using your fingers.

Using your a plastic opening tool, push out the battery by inserting it into the small groove at the top left corner of the battery and pushing out.

Step 5

Remove the SIM card by placing your index finger over it and sliding it out.
When you are ready to re-insert the SIM card make sure the pink side facing up.

Remove the SIM card by placing your index finger over it and sliding it out.

When you are ready to re-insert the SIM card make sure the pink side facing up.

Step 6

              Keypad

Unscrew the phone casing using a small screw driver. Remove the four screws on each corner on the back of the phone.
Screw sizes are 1.42mm in width and 3.37mm in length.

Unscrew the phone casing using a small screw driver. Remove the four screws on each corner on the back of the phone.

Screw sizes are 1.42mm in width and 3.37mm in length.

Step 7

Remove front casing by sliding a plastic opening tool between the chrome layer and the top cover.

Remove front casing by sliding a plastic opening tool between the chrome layer and the top cover.

Step 8

The buttons should come off with the front casing but sometimes they don’t. If that is the case simply remove them using your fingers and place them with the front cover.
If your keypad buttons are sticky you can clean them in this step.

The buttons should come off with the front casing but sometimes they don’t. If that is the case simply remove them using your fingers and place them with the front cover.

If your keypad buttons are sticky you can clean them in this step.

Step 9

              Front/Rear Facing Camera

Remove the back casing by taking the motherboard and back casing and pulling them apart.

Remove the back casing by taking the motherboard and back casing and pulling them apart.

Step 10

Using a small phillips #00 screw driver remove the three screws on the clear cover.
Screw sizes are 1.15mm in width and 1.51mm in length.

Using a small phillips #00 screw driver remove the three screws on the clear cover.

Screw sizes are 1.15mm in width and 1.51mm in length.

Step 11

The back camera is a circular piece at the top center of the phone that is sticking out.
The from camera is a circular piece at the top right side of the phone that is sticking out.
identify which camera you wish to replace, If it is still attached you must remove the headphone jack using the heat pen on your soldering station on top of the headphone jack until it becomes loose.
Gently remove the camera using tweezers.
At this point you can solder the new camera.

The back camera is a circular piece at the top center of the phone that is sticking out.

The from camera is a circular piece at the top right side of the phone that is sticking out.

identify which camera you wish to replace, If it is still attached you must remove the headphone jack using the heat pen on your soldering station on top of the headphone jack until it becomes loose.

Gently remove the camera using tweezers.

At this point you can solder the new camera.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors

                    Dioselina M Varela

Member since: 10/25/2014

261 Reputation

                                      2 Guides authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       Gateway, Team 1-1, Johnson Fall 2014                        

                                                  Member of Gateway, Team 1-1, Johnson Fall 2014 



                    GCC-JOHNSON-F14S1G1                     


                                            3 Members                     


                                            12 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team