Difficulty
Difficult
Steps
11
Time Required
50 minutes - 1 hour
Sections
1
- Display
- 11 steps
Flags
0
BackZTE Max XL
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Display
- Before disassembly, assure the phone is powered off.
- Use the SIM Card remover key, remove the SIM Card tray. To do this insert the key into the hole on the side of the phone near the SIM Card tray.
Before disassembly, assure the phone is powered off.
Use the SIM Card remover key, remove the SIM Card tray. To do this insert the key into the hole on the side of the phone near the SIM Card tray.
1024
Step 2
- Apply the iOpener to the back of the phone. For instructions on how to use the iOpener, use this guide
- On our phone there was adhesive on the top and bottom of the phone backing, so we specifically heated these areas.
- Do not heat the phone too much in one area - it may warp the plastic backing.
Apply the iOpener to the back of the phone. For instructions on how to use the iOpener, use this guide
On our phone there was adhesive on the top and bottom of the phone backing, so we specifically heated these areas.
Do not heat the phone too much in one area - it may warp the plastic backing.
Step 3
- Starting at one corner, wedge a plastic opening pick or tool underneath the plastic backing to start undoing the tabs that connect the backing to the phone.
- There are 3 tabs on top and bottom and 6 on each side.
Starting at one corner, wedge a plastic opening pick or tool underneath the plastic backing to start undoing the tabs that connect the backing to the phone.
There are 3 tabs on top and bottom and 6 on each side.
Step 4
- Remove the two 3.4 mm JIS #00 screws that hold the cable in place—one may be under a lock sticker.
Remove the two 3.4 mm JIS #00 screws that hold the cable in place—one may be under a lock sticker.
Step 5
- Use a nylon spudger to lift the press-fit connector and free the ribbon cable from the main part of the phone.
Use a nylon spudger to lift the press-fit connector and free the ribbon cable from the main part of the phone.
Step 6
- Remove all nineteen 3.4 mm JIS #00 screws from the perimeter of the back.
Remove all nineteen 3.4 mm JIS #00 screws from the perimeter of the back.
Step 7
- Use an opening tool between the screen and side trim battery cover to remove the screen.
Use an opening tool between the screen and side trim battery cover to remove the screen.
Step 8
- Use a nylon spudger to carefully lift the 6 press-fit connections free from the motherboard.
Use a nylon spudger to carefully lift the 6 press-fit connections free from the motherboard.
Step 9
- Using the iFixit opening tools carefully pry the edge of the battery away from the casing.
- Do not bend or puncture the battery during this process.
- If the battery does not lift away freely, use careful amounts of isopropyl alcohol to help soften the adhesive. Gently work a thin opening pick or plastic card along the underside of the battery, pushing the card through the adhesive while lifting the battery free.
Using the iFixit opening tools carefully pry the edge of the battery away from the casing.
Do not bend or puncture the battery during this process.
If the battery does not lift away freely, use careful amounts of isopropyl alcohol to help soften the adhesive. Gently work a thin opening pick or plastic card along the underside of the battery, pushing the card through the adhesive while lifting the battery free.
Step 10
- After taking off the battery and disconnecting all the metal tabs underneath, using the iOPener to break the adhesive between the display and the circuit.
- Do not heat the phone too much in one area
After taking off the battery and disconnecting all the metal tabs underneath, using the iOPener to break the adhesive between the display and the circuit.
Do not heat the phone too much in one area
Step 11
- Use the plastic opening pick in the iFixit kit to wedge between the display and circuit.
- Be sure not to damage the wire connecting the display to the circuit.
- Replace the display and resemble the device following the reverse order
Use the plastic opening pick in the iFixit kit to wedge between the display and circuit.
Be sure not to damage the wire connecting the display to the circuit.
Replace the display and resemble the device following the reverse order
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 2 other contributors
Isaac Ssaku
Member since: 04/11/2022
253 Reputation
1 Guide authored
Badges:
6
+3 more badges
Team
IUPUI, Team 1-2, Harley Spring 2022
Member of IUPUI, Team 1-2, Harley Spring 2022
IUPUI-HARLEY-S22S1G2
4 Members
3 Guides authored