Zte Blade Z Max Fingerprint Sensor Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          40 minutes

Sections

SIM Card
2 steps
Fingerprint Sensor
8 steps

Flags

BackZTE Blade Z Max
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              SIM Card

Turn the device on it side with the buttons away from you.
Using the SIM Card Eject Tool, insert the narrow end into the ejection hole.
Press firmly into the hole until the SIM card tray pops out far enough to grab with your fingers.

Turn the device on it side with the buttons away from you.

Using the SIM Card Eject Tool, insert the narrow end into the ejection hole.

Press firmly into the hole until the SIM card tray pops out far enough to grab with your fingers.

1024

Step 2

Pull the tray out with your fingers .
Remove the SIM card.

Pull the tray out with your fingers .

Remove the SIM card.

Step 3

              Fingerprint Sensor

Remove the one T2 screw from the side of the phone near where the SIM card tray was.

Remove the one T2 screw from the side of the phone near where the SIM card tray was.

Step 4

Insert a plastic opening tool into the space where the SIM card tray used to be.
Gently pry the back away form the phone frame until you hear and audible click of the back separating.

Insert a plastic opening tool into the space where the SIM card tray used to be.

Gently pry the back away form the phone frame until you hear and audible click of the back separating.

Step 5

Insert the plastic opening tool into the space you created between the phone back and frame.
Slide the plastic opening tool along the outside of the phone, underneath the back, to separate the rest of the clips holding the back onto the frame.

Insert the plastic opening tool into the space you created between the phone back and frame.

Slide the plastic opening tool along the outside of the phone, underneath the back, to separate the rest of the clips holding the back onto the frame.

Step 6

Rotate the back over to the side, being careful not to damage the fingerprint sensor ribbon cable.
Use a plastic opening tool to separate the fingerprint sensor from the back of the phone.
On reassembly, add a piece of simple scotch tape to hold the fingerprint sensor to the phone back.
Set the phone back aside.

Rotate the back over to the side, being careful not to damage the fingerprint sensor ribbon cable.

Use a plastic opening tool to separate the fingerprint sensor from the back of the phone.

On reassembly, add a piece of simple scotch tape to hold the fingerprint sensor to the phone back.

Set the phone back aside.

Step 7

Remove the 6 silver 2.9mm screws from the back of the phone with a JIS #000 bit.
Remove the 11 black 3.5mm screws with the same JIS #000 bit.

Remove the 6 silver 2.9mm screws from the back of the phone with a JIS #000 bit.

Remove the 11 black 3.5mm screws with the same JIS #000 bit.

Step 8

Turn the phone over, with the screen up.
Insert the opening tool between the screen and the silver trim that surrounds it.
Run the plastic opening tool around the circumference of the phone to separate the clips of that hold the trim to the frame.

Turn the phone over, with the screen up.

Insert the opening tool between the screen and the silver trim that surrounds it.

Run the plastic opening tool around the circumference of the phone to separate the clips of that hold the trim to the frame.

Step 9

Turn the phone back over, with the screen down.
Lift the trim piece off of the phone and set aside.

Turn the phone back over, with the screen down.

Lift the trim piece off of the phone and set aside.

Step 10

Using a plastic opening tool, separate the fingerprint ribbon connector from the motherboard.

Using a plastic opening tool, separate the fingerprint ribbon connector from the motherboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 3 other contributors

                    Ronald Weimar

Member since: 09/24/2018

1,399 Reputation

                                      6 Guides authored                  



                       Badges:
                       16







                                                        +13 more badges

Team

                       The Citadel Military College of South Carolina, Team S3-G7, Eggleston Fall 2018                        

                                                  Member of The Citadel Military College of South Carolina, Team S3-G7, Eggleston Fall 2018 



                    CMCSC-EGGLESTON-F18S3G7                     


                                            4 Members                     


                                            12 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team