Zoomer Meowzies Head Opening Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

Suggest a time??

Sections

Legs
3 steps
Head (Bottom)
6 steps

Flags

BackZoomer Meowzies
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Legs

Using the Triangle driver remove the four 7.5 mm screws.
The two front screws are deeper than the two on the back legs which may cause difficulties. These can be reached by putting the bit in first then carefully putting the driver on slightly (not all the way)

Using the Triangle driver remove the four 7.5 mm screws.

The two front screws are deeper than the two on the back legs which may cause difficulties. These can be reached by putting the bit in first then carefully putting the driver on slightly (not all the way)

1024

Step 2

Turn the device so that the the device is on its side.
Hold the back and belly on the device and gently pull apart.
Pulling with too much force might damage a few cables inside, so caution is needed.

Turn the device so that the the device is on its side.

Hold the back and belly on the device and gently pull apart.

Pulling with too much force might damage a few cables inside, so caution is needed.

Step 3

With insides exposed, grab leg and gently pull up and away from the body to detach them. Repeat for all legs needed.

With insides exposed, grab leg and gently pull up and away from the body to detach them. Repeat for all legs needed.

Step 4

              Head (Bottom)

Gently pry the ribbon cable from the connector.

Gently pry the ribbon cable from the connector.

Step 5

Using a soldering Iron, carefully heat the solder point around the silver wire and pull gently until the wire lifts free.
The soldering iron and solder get very hot, so caution is advised to avoid touching either directly.
This step may be skipped but if so care must be taken to not accidentally pull the wire from the contact. Skipping this step will limit the amount or room that is available to work with.

Using a soldering Iron, carefully heat the solder point around the silver wire and pull gently until the wire lifts free.

The soldering iron and solder get very hot, so caution is advised to avoid touching either directly.

This step may be skipped but if so care must be taken to not accidentally pull the wire from the contact. Skipping this step will limit the amount or room that is available to work with.

Step 6

Take the upper half of the device in hand.
Using the Philips #1 driver remove the two 9.5mm screws.
Remove the purple square collar around the neck of the device.
The wires can prove difficult to get through the opening in the collar. Move wires through the opening carefully.

Take the upper half of the device in hand.

Using the Philips #1 driver remove the two 9.5mm screws.

Remove the purple square collar around the neck of the device.

The wires can prove difficult to get through the opening in the collar. Move wires through the opening carefully.

Step 7

Turn the device so that it is on its side.
Holding the device’s head and back in each hand, pull apart to separate the head from the body.
Pull the wires through and manipulate carefully as needed to get them through and completely detach head.

Turn the device so that it is on its side.

Holding the device’s head and back in each hand, pull apart to separate the head from the body.

Pull the wires through and manipulate carefully as needed to get them through and completely detach head.

Step 8

Turn the head upside-down so that ears are facing down, and locate the four screws around the underside of the device’s head.
Use the Triangle screwdriver to remove the four 7.5mm screws.

Turn the head upside-down so that ears are facing down, and locate the four screws around the underside of the device’s head.

Use the Triangle screwdriver to remove the four 7.5mm screws.

Step 9

Hold the top and bottom halves of the head in each hand separately and gently pull away from each other to separate both halves.

Hold the top and bottom halves of the head in each hand separately and gently pull away from each other to separate both halves.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors

                    Mitchell Gentry

Member since: 02/14/2018

675 Reputation

                                      6 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       USF Tampa, Team S6-G2, Eyestone Spring 2018                        

                                                  Member of USF Tampa, Team S6-G2, Eyestone Spring 2018 



                    USFT-EYESTONE-S18S6G2                     


                                            3 Members                     


                                            8 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team