Difficulty

Difficult

Steps

6

Time Required

                          30 minutes - 1 hour

Sections

2

  • Back Cover
  • 3 steps
  • Motherboard
  • 3 steps

Flags

1

This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.

  • BackZoomer Jurassic World Indominus Rex

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Cover
  • Turn off and unplug Zoomer Jurassic World Indominus Rex from any power source before doing replacements.
  • Remove all eight (8) 9.3mm Phillips screws using Phillips #1 screwdriver.

Turn off and unplug Zoomer Jurassic World Indominus Rex from any power source before doing replacements.

Remove all eight (8) 9.3mm Phillips screws using Phillips #1 screwdriver.

1024

Step 2

  • Pry apart the back cover of the Jurassic Indominus Rex and the rest of the body using a spudger.
  • Do not take out the back cover immediately as it it still attached to the motherboard by a wire.

Pry apart the back cover of the Jurassic Indominus Rex and the rest of the body using a spudger.

Do not take out the back cover immediately as it it still attached to the motherboard by a wire.

Step 3

  • Disconnect the orange wire that connects the motherboard and the back cover.
  • Separate the back cover and the rest of the Zoomer Jurassic World Indominus Rex.
  • Gently press the tab on the side of the orange connector if you are having trouble disconnecting the wire.

Disconnect the orange wire that connects the motherboard and the back cover.

Separate the back cover and the rest of the Zoomer Jurassic World Indominus Rex.

Gently press the tab on the side of the orange connector if you are having trouble disconnecting the wire.

Step 4

              Motherboard
  • Let the toy rest firmly on a flat surface before processing to the next step.
  • Gently pull each wire out of the connector on the motherboard. Use a set of tweezers, if necessary.

Let the toy rest firmly on a flat surface before processing to the next step.

Gently pull each wire out of the connector on the motherboard. Use a set of tweezers, if necessary.

Step 5

  • Remove the two (2) #0 7.5mm phillips screws from the left side of the motherboard.
  • Remove the one (1) 7.5mm #0 phillips screw from the right side of the motherboard.

Remove the two (2) #0 7.5mm phillips screws from the left side of the motherboard.

Remove the one (1) 7.5mm #0 phillips screw from the right side of the motherboard.

Step 6

  • Use a soldering iron to remove the red and black wires from the motherboard .
  • Soldering technique guide from iFixit can be found here.
  • Use caution while soldering to avoid being burned.

Use a soldering iron to remove the red and black wires from the motherboard .

Soldering technique guide from iFixit can be found here.

Use caution while soldering to avoid being burned.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Anh Le

Member since: 01/20/2016

504 Reputation

                                      3 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       USF Tampa, Team 10-3, Remmell Spring 2016                        

                                                  Member of USF Tampa, Team 10-3, Remmell Spring 2016 



                    USFT-REMMELL-S16S10G3                     


                                            4 Members                     


                                            7 Guides authored