Difficulty
Moderate
Steps
11
Time Required
10 - 15 minutes
Sections
2
- Case
- 4 steps
- Motherboard
- 7 steps
Flags
1
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
BackZoom H6 Handy Recorder
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Case
- Place device face up and pry off the four knobs using the flat end of the plastic opening tool.
- You may need to stabilize the device with the other hand.
Place device face up and pry off the four knobs using the flat end of the plastic opening tool.
You may need to stabilize the device with the other hand.
1024
Step 2
- With device facedown, lift the four rubber feet from the device using tweezers or fingernails.
With device facedown, lift the four rubber feet from the device using tweezers or fingernails.
Step 3
- With device still facedown, unscrew six (PH #1), 9mm screws; two located in center of back side of device right above the battery cover, and four under the rubber feet.
- An electronics screwdriver small enough to fit in hole (4mm diameter), but long enough to reach the screws (at least 2cm) will be required to unscrew the screws.
With device still facedown, unscrew six (PH #1), 9mm screws; two located in center of back side of device right above the battery cover, and four under the rubber feet.
An electronics screwdriver small enough to fit in hole (4mm diameter), but long enough to reach the screws (at least 2cm) will be required to unscrew the screws.
Step 4
- With the bottom of the device on a table, lift the top of the device and gently place it aside.
With the bottom of the device on a table, lift the top of the device and gently place it aside.
Step 5
Motherboard
- Unscrew three (PH #1), 7mm screws from the display backing and gently flip over.
Unscrew three (PH #1), 7mm screws from the display backing and gently flip over.
Step 6
- Using a plastic opening tool, unlatch the clip and carefully unplug the ribbon connector from the device.
- Set the button board aside.
Using a plastic opening tool, unlatch the clip and carefully unplug the ribbon connector from the device.
Set the button board aside.
Step 7
- Unscrew four (PH #1), 8mm screws from the motherboard.
Unscrew four (PH #1), 8mm screws from the motherboard.
Step 8
- Disconnect wire from motherboard using tweezers.
- Do not touch the motherboard with metal tweezers. Only touch the plastic part of the plugged-in wire.
Disconnect wire from motherboard using tweezers.
Do not touch the motherboard with metal tweezers. Only touch the plastic part of the plugged-in wire.
Step 9
- Turn device 180 degrees to unscrew two (PH #1), 8mm screws from the mic connector.
Turn device 180 degrees to unscrew two (PH #1), 8mm screws from the mic connector.
Step 10
- Gently remove three ribbon connectors from the device.
- The first is connected to the mic connector.
- The second is connected to the base of the device, and the third is connected to the power switch on the side of the device; turn the device 180 degrees, and the connectors are near the top of the device next to the “LINE OUT” plug-in (directly behind the device display).
- It’s best to use tweezers to remove the two ribbon connectors behind the display.
- Avoid touching anything but the ribbon connectors with the metal tweezers.
Gently remove three ribbon connectors from the device.
The first is connected to the mic connector.
The second is connected to the base of the device, and the third is connected to the power switch on the side of the device; turn the device 180 degrees, and the connectors are near the top of the device next to the “LINE OUT” plug-in (directly behind the device display).
It’s best to use tweezers to remove the two ribbon connectors behind the display.
Avoid touching anything but the ribbon connectors with the metal tweezers.
Step 11
- Gently lift the motherboard from the base of the device and set aside.
Gently lift the motherboard from the base of the device and set aside.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 2 other contributors
Cheryl Avery
Member since: 02/14/2018
331 Reputation
1 Guide authored
Badges:
9
+6 more badges
Team
USF Tampa, Team S5-G2, Eyestone Spring 2018
Member of USF Tampa, Team S5-G2, Eyestone Spring 2018
USFT-EYESTONE-S18S5G2
4 Members
8 Guides authored
leito - Jul 26, 2018
Reply
Good night Mr.
I have a H6 recorder H.6 handy recorder, never use, but the battery stay in and it leak in the box.
When i remove the leaking battery, and i renew the battery the recorder did not start. According a technician the aparatus have to be open and chance the plate, but we does not have those technician on the island. please advice.
Edgar.
tahitibob57 - Sep 19, 2018
Reply
hello, i just have a question, where can i find this parts?
Adebanjo Sulaimon - Oct 22, 2018
Reply
Can i get Zoom H6 Handy Recorder Motherboard only i need it and the price
David Lesage - Sep 30, 2019
Yes here ! https://shop.audiotronic.fr/en/61-h6
Caro - Apr 10, 2020
Reply
What was the problem? How do you diagnose a bad LCD screen? My screen goes white and nothing else comes on. So there is power, but nothing comes on the screen but the white background.