Difficulty
Moderate
Steps
7
Time Required
15 minutes
Sections
1
- Zipper Insertion Pin
- 7 steps
Flags
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
BackClothing
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Zipper Insertion Pin
- Examine the damaged zipper.
Examine the damaged zipper.
1024
Step 2
- Cut the broken insertion pin off the zipper. If the pin is missing (like in the photo), cut the frayed fabric. Do not cut the zipper teeth.
Cut the broken insertion pin off the zipper. If the pin is missing (like in the photo), cut the frayed fabric. Do not cut the zipper teeth.
Step 3
- Find an article of clothing no longer in use with a zipper. The insertion pin must be the same length as the broken/ missing one, but it does not matter if it is plastic or metal.
Find an article of clothing no longer in use with a zipper. The insertion pin must be the same length as the broken/ missing one, but it does not matter if it is plastic or metal.
Step 4
- Cut the working insertion pin from the old clothing off the zipper. Do not cut the plastic square backing or too much material. You must have enough fabric to sew.
Cut the working insertion pin from the old clothing off the zipper. Do not cut the plastic square backing or too much material. You must have enough fabric to sew.
Step 5
- Line up the new insertion pin on the broken coat.
Line up the new insertion pin on the broken coat.
Step 6
- Sew the insertion pin into place.
Sew the insertion pin into place.
Step 7
- Test the zipper.
Test the zipper.
If the pin does not line up correctly, take out the thread and re-sew.
Cancel: I did not complete this guide.
10 other people completed this guide.
Author
with 3 other contributors
Caitlin Dillon
Member since: 03/07/2019
424 Reputation
1 Guide authored
Badges:
9
+6 more badges
Team
Missouri Western, Team S1-G6, Cools Stephens Spring 2019
Member of Missouri Western, Team S1-G6, Cools Stephens Spring 2019
MWSU-COOLS STEPHENS-S19S1G6
1 Member
6 Guides authored
Amy Pegram - Oct 15, 2019
Reply
Hi, I have a north face jacket and the zipper is fine but the plastic square backing is what’s missing so I can’t zip it up. Do you know what that’s really called so I can find a replacement? Or do you know what I can replace it with? Thanks, Amy
mattgrieser - Sep 16, 2021
https://doitbetteryourself.club/wp-conte…
Jacques Farges - Nov 30, 2019
Reply
Instead of cutting a notch out, I removed the stitching at the edge of the coat to expose the entire zipper body end, and completely cut the end off. Then I stitched a complete new end on. The advantage was that it provided the maximum mechanical strength to keep the insertion pin aligned.
Careful when at the cut lines, do not pull on any threads, some are loose, but I have a way to fix that later. Then stitch using long stiches to avoid the areas too close to the cut lines where the threads are loose.
Finally, I zip the 2 halves together in order to align all the parts together into their final relative positions, and use a Bondic glue pen on all stitches and areas around the cuts where the loose threads are. When I cure with the UV light, the result is much stronger than just the threads. I was careful to not apply any of the epoxy close to the zipper, so that I don’t block the passage of the zipper slider.
Then I lightly sand to remove any sharp edges, and sew the zipper tape back to the jacket.
Brittney McKnight - Mar 13, 2020
I will need to see a YouTube video on that lol
Caitlin Dillon - Dec 28, 2020
That’s a great solution. I considered that, but it seemed like way more work, so I opted for a simpler fix. You could also replace the entire zipper if you wanted!
