Difficulty
Moderate
Steps
10
Time Required
10 - 15 minutes
Sections
3
- Back Panel
- 2 steps
- Motherboard
- 7 steps
- Camera
- 1 step
Flags
0
BackZenithink ZTPAD ZT280 C91
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Panel
- Remove the two screws on the bottom using a Phillips #00 screwdriver.
- For differentiation purposes, these screws are 4mm long.
Remove the two screws on the bottom using a Phillips #00 screwdriver.
For differentiation purposes, these screws are 4mm long.
1024
Step 2
- Using a spudger, start prying the case apart by working around the edge slowly.
- Be careful not to damage any of the latches that hold the back panel in place, especially if you are using a metal spudger.
- While prying, be careful to not lose the power and volume buttons; the case is the only thing holding them in place so they will easily come out once the panel has been removed
- Be careful to not damage the speaker cables, they will still be connecting both panels.
Using a spudger, start prying the case apart by working around the edge slowly.
Be careful not to damage any of the latches that hold the back panel in place, especially if you are using a metal spudger.
While prying, be careful to not lose the power and volume buttons; the case is the only thing holding them in place so they will easily come out once the panel has been removed
Be careful to not damage the speaker cables, they will still be connecting both panels.
Step 3
Motherboard
- Peel back the touch interface chip (which is on the top right of the motherboard, covered in yellow tape.)
Peel back the touch interface chip (which is on the top right of the motherboard, covered in yellow tape.)
Step 4
- Flip up the small gate and unplug the ribbon cable shown.
Flip up the small gate and unplug the ribbon cable shown.
Step 5
- Using a Phillips #00 screwdriver, remove the screws highlighted with the orange rings as shown in the picture.
- For differentiation purposes, these screws are 3.5mm long.
Using a Phillips #00 screwdriver, remove the screws highlighted with the orange rings as shown in the picture.
For differentiation purposes, these screws are 3.5mm long.
Step 6
- Slide back the plastic latch for the main display cable.
- Carefully unplug the cable with tweezers.
Slide back the plastic latch for the main display cable.
Carefully unplug the cable with tweezers.
Step 7
- Slide back the plastic latch for the camera cable.
- Carefully unplug the cable with tweezers.
Slide back the plastic latch for the camera cable.
Step 8
- Peel back the reflective tape.
Peel back the reflective tape.
Step 9
- Lift up the motherboard assembly, starting by lifting up the top.
- Be careful not to damage any of the ports on the underside of the tablet.
- The camera cable will slide through a small notch and end up underneath the board.
Lift up the motherboard assembly, starting by lifting up the top.
Be careful not to damage any of the ports on the underside of the tablet.
The camera cable will slide through a small notch and end up underneath the board.
Step 10
Camera
- Peel back the adhesive tape holding the camera in place.
- Remove the camera from the device.
Peel back the adhesive tape holding the camera in place.
Remove the camera from the device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 2 other contributors
Keelie Beach
Member since: 09/21/2018
417 Reputation
3 Guides authored
Badges:
6
+3 more badges
Team
University of North Texas, Team S6-G1, Thompson Fall 2018
Member of University of North Texas, Team S6-G1, Thompson Fall 2018
UNT-THOMPSON-F18S6G1
3 Members
5 Guides authored
