Zeal Optics Ion Lcd Backlight Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Lens
5 steps
Camera Assembly
11 steps
Viewfinder Lens Assembly
7 steps
LCD Assembly
1 step
LCD
2 steps
LCD Backlight
1 step

Flags

BackZeal Optics iON
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Lens

In the next few steps, you will be releasing the clips that hold the lens in place. Do not try to completely remove the lens until all the clips have been released.
Hold the iON in your hands with your thumbs on the clips next to the middle of the lens.
Pull the rubber housing apart to release the first two clips.

In the next few steps, you will be releasing the clips that hold the lens in place. Do not try to completely remove the lens until all the clips have been released.

Hold the iON in your hands with your thumbs on the clips next to the middle of the lens.

Pull the rubber housing apart to release the first two clips.

1024

Step 2

Grab the inside of the plastic nose rest with your thumb and index finger.
Rotate the nose rest upwards until you feel that it is free from the lens.

Grab the inside of the plastic nose rest with your thumb and index finger.

Rotate the nose rest upwards until you feel that it is free from the lens.

Step 3

Rotate the device 180 degrees.
Grab the top of the goggle frame that holds the camera assembly.
Rotate the frame outwards until you feel that the clips inside it are free.

Rotate the device 180 degrees.

Grab the top of the goggle frame that holds the camera assembly.

Rotate the frame outwards until you feel that the clips inside it are free.

Step 4

While firmly holding the goggles with the palm of one hand, grab the top right corner of the frame and rotate it away from the lens.

While firmly holding the goggles with the palm of one hand, grab the top right corner of the frame and rotate it away from the lens.

Step 5

The lens should now be barely attached to the frame. If it still feels firmly attached, repeat any necessary steps to free the clips.
While holding the goggles in one hand, use the other to grab the lens from opposite ends, and rotate it out of the housing and away from any remaining clips.

The lens should now be barely attached to the frame. If it still feels firmly attached, repeat any necessary steps to free the clips.

While holding the goggles in one hand, use the other to grab the lens from opposite ends, and rotate it out of the housing and away from any remaining clips.

Step 6

              Camera Assembly

Remove the four 7.1 mm Phillips screws securing the camera housing to the goggle frame.

Remove the four 7.1 mm Phillips screws securing the camera housing to the goggle frame.

Step 7

Peel back the rubber battery cover from the inner left side of the frame.
While firmly holding the battery cover, pull the bottom of the strap mount cover up and off of the frame

Peel back the rubber battery cover from the inner left side of the frame.

While firmly holding the battery cover, pull the bottom of the strap mount cover up and off of the frame

Step 8

Once the bottom is free, continue pulling to free the top of the strap mount cover from the frame.

Once the bottom is free, continue pulling to free the top of the strap mount cover from the frame.

Step 9

Pull the battery out of its recess in the frame.
The battery is connected to the entire camera assembly and cannot be completely removed by itself.

Pull the battery out of its recess in the frame.

The battery is connected to the entire camera assembly and cannot be completely removed by itself.

Step 10

Peel the rubber keypad cover up from the inner right side of the frame.
While firmly holding the keypad cover, pull the top of the strap mount cover up and off of the frame

Peel the rubber keypad cover up from the inner right side of the frame.

While firmly holding the keypad cover, pull the top of the strap mount cover up and off of the frame

Step 11

Once the bottom is free, continue pulling to free the bottom of the strap mount cover from the frame.

Once the bottom is free, continue pulling to free the bottom of the strap mount cover from the frame.

Step 12

Hold the strap mount cover away from the frame and remove the keypad.

Hold the strap mount cover away from the frame and remove the keypad.

Step 13

Grab the viewfinder housing and pull it out of its recess.
Just like the battery, the viewfinder housing is connected to the rest of the camera assembly and cannot be removed by itself.

Grab the viewfinder housing and pull it out of its recess.

Just like the battery, the viewfinder housing is connected to the rest of the camera assembly and cannot be removed by itself.

Step 14

Place one of your hands near the center of the frame with your thumb next to the camera housing.
With your other hand, grab the camera housing and pull it up and out of the frame.

Place one of your hands near the center of the frame with your thumb next to the camera housing.

With your other hand, grab the camera housing and pull it up and out of the frame.

Step 15

Remove the viewfinder assembly by pulling it through the opening in the top of the frame.

Remove the viewfinder assembly by pulling it through the opening in the top of the frame.

Step 16

In the same manner described above, remove the battery from the frame.

In the same manner described above, remove the battery from the frame.

Step 17

              Viewfinder Lens Assembly

Remove the two 7.5 mm Phillips screws on the front of the viewfinder housing.
Flip the viewfinder housing over 180 degrees.
Remove the four 7.1 mm Phillips screws from the back of the viewfinder housing.

Remove the two 7.5 mm Phillips screws on the front of the viewfinder housing.

Flip the viewfinder housing over 180 degrees.

Remove the four 7.1 mm Phillips screws from the back of the viewfinder housing.

Step 18

Pull the two halves of the viewfinder housing apart.

Pull the two halves of the viewfinder housing apart.

Step 19

Use the tip of a spudger to flip up the retaining flap on the LCD ribbon cable ZIF connector.
Be sure to pry up on the hinged flap, not the connector itself.

Use the tip of a spudger to flip up the retaining flap on the LCD ribbon cable ZIF connector.

Be sure to pry up on the hinged flap, not the connector itself.

Step 20

Use the tip of a spudger to push out the retaining clip on the viewfinder backlight ribbon cable ZIF connector.

Use the tip of a spudger to push out the retaining clip on the viewfinder backlight ribbon cable ZIF connector.

Step 21

Using your fingers or tweezers, gently pull out the backlight ribbon cable from its connector on the button board.

Using your fingers or tweezers, gently pull out the backlight ribbon cable from its connector on the button board.

Step 22

Using your fingers or tweezers, remove the LCD ribbon cable from its connector on the button board.

Using your fingers or tweezers, remove the LCD ribbon cable from its connector on the button board.

Step 23

Remove the viewfinder lens assembly from the viewfinder housing.

Remove the viewfinder lens assembly from the viewfinder housing.

Step 24

              LCD Assembly

Use your thumbs to lift the tabs holding the viewfinder lens to the LCD assembly.
Pull the viewfinder lens off of the viewfinder LCD.

Use your thumbs to lift the tabs holding the viewfinder lens to the LCD assembly.

Pull the viewfinder lens off of the viewfinder LCD.

Step 25

LCD

Use your thumb to push the LCD bracket tab away from the LCD.
Remove the LCD bracket from the LCD and backlight.

Use your thumb to push the LCD bracket tab away from the LCD.

Remove the LCD bracket from the LCD and backlight.

Step 26

Using your thumbs, pull the four white tabs on the backlight away from the LCD panel.
Remove the LCD from the backlight.

Using your thumbs, pull the four white tabs on the backlight away from the LCD panel.

Remove the LCD from the backlight.

Step 27

              LCD Backlight

The LCD backlight remains.

The LCD backlight remains.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors

                    Eric Flores

Member since: 07/31/2012

128 Reputation

                                      9 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Introduction#

What you need#

Introduction

What you need