Difficulty
Moderate
Steps
7
Time Required
30 minutes
Sections
2
- Motor
- 6 steps
- Arm
- 1 step
Flags
0
BackYuneec Typhoon H Plus
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Motor
- Flip the drone over so the bottom is facing upwards.
- Remove ten 9.5mm Hex 2 screws attached to the bottom shell.
Flip the drone over so the bottom is facing upwards.
Remove ten 9.5mm Hex 2 screws attached to the bottom shell.
1024
Step 2
- Carefully detach the top billit piece from the drone. There are internal clips that need to be detached from the top piece in order for the entire unit to come off.
- Once the lid is off, detach the wire that holds the lid to the body. Press down on the clip and slide the wire out.
Carefully detach the top billit piece from the drone. There are internal clips that need to be detached from the top piece in order for the entire unit to come off.
Once the lid is off, detach the wire that holds the lid to the body. Press down on the clip and slide the wire out.
Step 3
- Find the base of the arm you are replacing and remove the electrical tape.
- Disconnect the red, black, and blue wires. Also disconnect the white clip that is associated with those same wires.
- You may need a pair of pliers to get enough grip to disconnect the three wires.
Find the base of the arm you are replacing and remove the electrical tape.
Disconnect the red, black, and blue wires. Also disconnect the white clip that is associated with those same wires.
You may need a pair of pliers to get enough grip to disconnect the three wires.
Step 4
- Find the pin that holds the arm by pulling down the bottom shell. Use a Hex bit 2 screwdriver to remove it
- After removing the pin, pull the arm and wires out of the drone.
Find the pin that holds the arm by pulling down the bottom shell. Use a Hex bit 2 screwdriver to remove it
After removing the pin, pull the arm and wires out of the drone.
Step 5
- Use the wrench tool from the Yuneec drone box to remove the bottom cap from the motor mount. Twist clockwise until it pops; then it will slide out easily.
Use the wrench tool from the Yuneec drone box to remove the bottom cap from the motor mount. Twist clockwise until it pops; then it will slide out easily.
Step 6
- Disconnect the electrical board from the wire and thread the clip through the arm to the side with the motor to remove the entire motor/wire assembly.
- After both sides of the wire are on the side with the motor, pull the wires through the length of the arm.
Disconnect the electrical board from the wire and thread the clip through the arm to the side with the motor to remove the entire motor/wire assembly.
After both sides of the wire are on the side with the motor, pull the wires through the length of the arm.
Step 7
Arm
- Remove the small Phillips #000 screw that holds the arm clip in place.
- Use iFixit’s metal spudger to pry up on the clip to release it from the arm and pull it out with your fingers.
Remove the small Phillips #000 screw that holds the arm clip in place.
Use iFixit’s metal spudger to pry up on the clip to release it from the arm and pull it out with your fingers.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 2 other contributors
Theron Dale
Member since: 01/23/2020
91 Reputation
1 Guide authored
Badges:
6
+3 more badges
Team
Cal Poly, Team S2-G1, White Winter 2020
Member of Cal Poly, Team S2-G1, White Winter 2020
CPSU-WHITE-W20S2G1
4 Members
5 Guides authored
Reon Sharp - Apr 1, 2021
Reply
Would this be the same process for the Yuneec H520?