Yuneec St10 Plus Camera Switch Spring Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          10 minutes

Sections

Battery
3 steps
Camera Switch
8 steps
Camera Switch Spring
2 steps

Flags

BackYuneec ST10 Plus
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Flip the controller upside down to access the battery compartment.
Grab the compartment door and pull down.

Flip the controller upside down to access the battery compartment.

Grab the compartment door and pull down.

1024

Step 2

Gently lift the blue tab connected to the battery in order to remove the battery from its housing.

Gently lift the blue tab connected to the battery in order to remove the battery from its housing.

Step 3

To disconnect the battery from the remote, grab the red and black connectors.
Pull gently on connectors until they disconnect.

To disconnect the battery from the remote, grab the red and black connectors.

Pull gently on connectors until they disconnect.

Step 4

              Camera Switch

Grab ahold of the top of the black cap on the button with the pliers and pull up forcefully.

Grab ahold of the top of the black cap on the button with the pliers and pull up forcefully.

Step 5

Twist counter clockwise on the silver portion of the device with a pair of pliers.

Twist counter clockwise on the silver portion of the device with a pair of pliers.

Step 6

Slide the Jimmy underneath the rubber grips and pry upwards.
With your free hand grasp the rubber grips and pull upward to remove it.

Slide the Jimmy underneath the rubber grips and pry upwards.

With your free hand grasp the rubber grips and pull upward to remove it.

Step 7

Remove the six 1.3 cm screws located on the back panel of the remote using the 5.5mm hex screw bit.

Remove the six 1.3 cm screws located on the back panel of the remote using the 5.5mm hex screw bit.

Step 8

Remove the four 6mm screws from the handle using the 4mm hex driver bit.

Remove the four 6mm screws from the handle using the 4mm hex driver bit.

Step 9

Carefully pull up and over on the back panel to remove. Take your time because there are wires connecting the two panels that can easily torn.

Carefully pull up and over on the back panel to remove. Take your time because there are wires connecting the two panels that can easily torn.

Step 10

Flip your device.
Once the silver cover holding the switch in place is removed, remove the switch by grabbing it and pulling back towards you.

Flip your device.

Once the silver cover holding the switch in place is removed, remove the switch by grabbing it and pulling back towards you.

Step 11

Once the switch is removed, disconnect the switch from the circuit board by pulling the cable from the cable connector.
The cable will come out by pulling it away from you if the bottom of the controller is oriented closer to you.

Once the switch is removed, disconnect the switch from the circuit board by pulling the cable from the cable connector.

The cable will come out by pulling it away from you if the bottom of the controller is oriented closer to you.

Step 12

              Camera Switch Spring

Carefully pry up the small metal feet surrounding the red switch connector on both sides using a metal spudger.
There are four feet located on the silver portion of the switch.

Carefully pry up the small metal feet surrounding the red switch connector on both sides using a metal spudger.

There are four feet located on the silver portion of the switch.

Step 13

Make sure to pull up and out where the spring connects. Do not pull from the middle of the spring or it will snap it.
With the angled tweezers pinch the end of the spring with the loop and gently push the spring down and back, then lift up.
Pinch the spring with the angled tweezers, bringing it to a vertical position. Then push down on the spring to remove it from the port that it is connected to.
Pull the spring away from the housing.

Make sure to pull up and out where the spring connects. Do not pull from the middle of the spring or it will snap it.

With the angled tweezers pinch the end of the spring with the loop and gently push the spring down and back, then lift up.

Pinch the spring with the angled tweezers, bringing it to a vertical position. Then push down on the spring to remove it from the port that it is connected to.

Pull the spring away from the housing.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors

                    Joshua Collins

Member since: 01/27/2020

577 Reputation

                                      4 Guides authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       Embry-Riddle Aeronautical University, Team S6-G6, Watkins Spring 2020                        

                                                  Member of Embry-Riddle Aeronautical University, Team S6-G6, Watkins Spring 2020 



                    ERAU-WATKINS-S20S6G6                     


                                            5 Members                     


                                            5 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team