Difficulty
Moderate
Steps
13
Time Required
50 minutes
Sections
1
- Camera
- 13 steps
Flags
4
Action Shots
Be an action hero! This guide needs images that better demonstrate how to perform specific actions.
Incorrect Tools
Help make this guide better by using the correct tools in images and/or text.
Missed a Step
Oops! This guide is currently missing some important steps.
Missing Details
Some of this guide’s details are missing. Help users by adding tools, difficulty, or time.
BackYuneec Breeze 4K
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Camera
- Before you begin start by putting on a ESD wrist strap to prevent ESD damage and remove the battery.
- Once the battery is taken out, flip over the drone so that the cameras are now facing up.
Before you begin start by putting on a ESD wrist strap to prevent ESD damage and remove the battery.
Once the battery is taken out, flip over the drone so that the cameras are now facing up.
1024
Step 2
- Using small pliers grip the connector of the wire and pull it out slowly.
Using small pliers grip the connector of the wire and pull it out slowly.
Step 3
- Remove the four white rubber dampeners located in each corner of the frame that hold the it in place.
Remove the four white rubber dampeners located in each corner of the frame that hold the it in place.
Step 4
- Unplug the two vertical plugs located in the rear of the M7 board.
Unplug the two vertical plugs located in the rear of the M7 board.
Step 5
- Slightly lift the M7 board to remove the two plugs located under the rear of the board.
Slightly lift the M7 board to remove the two plugs located under the rear of the board.
Step 6
- Once all plugs on top of the M7 board are disconnected, carefully lift the M7 board onto its side and remove all plugs on the bottom.
Once all plugs on top of the M7 board are disconnected, carefully lift the M7 board onto its side and remove all plugs on the bottom.
Step 7
- Tilt the M7 board onto its side. Using the Phillips #00 screwdriver remove the two black screws connected to the large black two pronged input.
Tilt the M7 board onto its side. Using the Phillips #00 screwdriver remove the two black screws connected to the large black two pronged input.
Step 8
- Using a pair of pliers pull apart the battery connector.
Using a pair of pliers pull apart the battery connector.
Step 9
- Flip over the entire frame along with the M7 board and the A9 board.
Flip over the entire frame along with the M7 board and the A9 board.
Step 10
- There will be 4 screws that hold the A9 board together. Using a H1.5 Alan bit unscrew those bolts to take the A9 board apart.
There will be 4 screws that hold the A9 board together. Using a H1.5 Alan bit unscrew those bolts to take the A9 board apart.
Step 11
- Unplug the only wire that is connected to the A9 board.
Unplug the only wire that is connected to the A9 board.
Step 12
- Pull apart the frame from the other board. The camera will be connected by a plug and it should pull out easily.
Pull apart the frame from the other board. The camera will be connected by a plug and it should pull out easily.
Step 13
- Unscrew the four screws that are holding the camera to the frame.
Unscrew the four screws that are holding the camera to the frame.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 4 other contributors
Wes Knutson
Member since: 10/04/2018
481 Reputation
3 Guides authored
Badges:
11
+8 more badges
Team
UW Stout, Team S6-G5, Ogden Fall 2018
Member of UW Stout, Team S6-G5, Ogden Fall 2018
UWSTOUT-OGDEN-F18S6G5
4 Members
4 Guides authored
neonjohn25 - May 25, 2019
Reply
Excellent! I don’t think that the process could of have been any more clear than this.
