Xiaomi Redmi Note Headphone Jack Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          2 hours

Sections

Battery
3 steps
Midframe
2 steps
Front-Facing Camera
1 step
Rear Camera
1 step
Motherboard
7 steps
Headphone Jack
2 steps

Flags

Needs More Images

A few more images would make this guide’s procedures crystal clear.

BackXiaomi Redmi Note
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Make sure the Xiaomi Redmi Note is powered off before removing the battery.
Insert the plastic opening tool between the charging port and the rear case.
Pry the end of the rear case up from the charging port.

Make sure the Xiaomi Redmi Note is powered off before removing the battery.

Insert the plastic opening tool between the charging port and the rear case.

Pry the end of the rear case up from the charging port.

1024

Step 2

Run the plastic opening tool along the seam on the side of the phone to remove the rear casing.

Run the plastic opening tool along the seam on the side of the phone to remove the rear casing.

Step 3

Locate the indentation at the bottom of the battery.
Place a finger in the indentation and lift up to remove the battery.

Locate the indentation at the bottom of the battery.

Place a finger in the indentation and lift up to remove the battery.

Step 4

              Midframe

Remove twelve 3.5mm Phillips #00 screws from the midframe.

Remove twelve 3.5mm Phillips #00 screws from the midframe.

Step 5

Insert a plastic opening into the seam between the midframe and the bottom frame of the phone.
Run the plastic opening tool along the seam.
Pry up the midframe with the plastic opening tool.
Once the midframe has been sufficiently lifted with the tool, place a hand underneath the edge to lift the entire component out of the frame.
There will be snapping sounds as the clips on the midframe disconnect from the phone.

Insert a plastic opening into the seam between the midframe and the bottom frame of the phone.

Run the plastic opening tool along the seam.

Pry up the midframe with the plastic opening tool.

Once the midframe has been sufficiently lifted with the tool, place a hand underneath the edge to lift the entire component out of the frame.

There will be snapping sounds as the clips on the midframe disconnect from the phone.

Step 6

              Front-Facing Camera

Use tweezers to lift the retaining flap of the zero insertion force (ZIF) connector to the upright position.
Use tweezers to pull the ribbon cable out of the ZIF connector.
Remove the front-facing camera from the motherboard.

Use tweezers to lift the retaining flap of the zero insertion force (ZIF) connector to the upright position.

Use tweezers to pull the ribbon cable out of the ZIF connector.

Remove the front-facing camera from the motherboard.

Step 7

              Rear Camera

Disconnect the rear-facing camera from the motherboard by pulling out the press-fit connector to its left.

Disconnect the rear-facing camera from the motherboard by pulling out the press-fit connector to its left.

Step 8

              Motherboard

Locate the three ZIF connectors on the motherboard.

Locate the three ZIF connectors on the motherboard.

Step 9

Use tweezers to lift the retaining flap on the ZIF connector to the upright position.
Pull the ribbon cable out of the connector by pulling to the left.
Repeat these steps for the other two ZIF connectors.

Use tweezers to lift the retaining flap on the ZIF connector to the upright position.

Pull the ribbon cable out of the connector by pulling to the left.

Repeat these steps for the other two ZIF connectors.

Step 10

Locate the antenna cable on the bottom right of the motherboard and use tweezers to lift the cable off of the motherboard.

Locate the antenna cable on the bottom right of the motherboard and use tweezers to lift the cable off of the motherboard.

Step 11

Remove the two 2.9mm Philips #00 screws.

Remove the two 2.9mm Philips #00 screws.

Step 12

Flip over the motherboard to reveal the back.
Use a plastic opening tool to pry off the snap fit connector, located on the bottom right off of the motherboard.

Flip over the motherboard to reveal the back.

Use a plastic opening tool to pry off the snap fit connector, located on the bottom right off of the motherboard.

Step 13

Lift up the motherboard and turn it over to place it by the side of the phone.
Do not attempt to remove the motherboard at this stage. Pulling on the board can damage its connection to the vibrating motor.

Lift up the motherboard and turn it over to place it by the side of the phone.

Do not attempt to remove the motherboard at this stage. Pulling on the board can damage its connection to the vibrating motor.

Step 14

Use tweezers to peel the vibrating motor off the frame of the phone.
The vibrating motor is glued to the frame, so do not be afraid to use force to dislodge it.

Use tweezers to peel the vibrating motor off the frame of the phone.

The vibrating motor is glued to the frame, so do not be afraid to use force to dislodge it.

Step 15

              Headphone Jack

Flip over the motherboard and locate the headphone jack at the top left corner.
Desolder the 6 soldered connections on the sides of the headphone jack from the motherboard.
Learn how to solder and desolder here.

Flip over the motherboard and locate the headphone jack at the top left corner.

Desolder the 6 soldered connections on the sides of the headphone jack from the motherboard.

Learn how to solder and desolder here.

Step 16

Use tweezers to pull off the headphone jack from the motherboard.

Use tweezers to pull off the headphone jack from the motherboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      7 other people completed this guide.

Author

                                      with 2 other contributors

                    Zongyi Li

Member since: 04/26/2017

1,497 Reputation

                                      3 Guides authored                  



                       Badges:
                       24







                                                        +21 more badges

Team

                       Cal Poly, Team S22-G4, Livingston Spring 2017                        

                                                  Member of Cal Poly, Team S22-G4, Livingston Spring 2017 



                    CPSU-LIVINGSTON-S17S22G4                     


                                            4 Members                     


                                            16 Guides authored

Hemant Kshirsagar - Oct 18, 2017

You have mentioned it in detailed, but can you mentioned the actual way or sequence of soldering six legs of the jack?

Can you mention the part number of redmi note headphone jack?

link where the jack will be available.

manu tm manu - Sep 21, 2018

I want to buy head phone jack, where the jack will

iSparehub. Com - Nov 5, 2018

You can visit iSparehub.com

Mathias Bork - Nov 9, 2018

Hey, hast du eine Ahnung, wo man eine Kopfhörerbuchse als Ersatzteil für ein Xiaomi Redmi Note 5 Global herbekommt? Das wäre klasse.

Rinku Poonia - Jun 15, 2019

Redmi note 4 earphone jack replacement Ka price Kya hai

Needs More Images#

Introduction#

What you need#

Team#

Needs More Images

Introduction

What you need

Team