Difficulty

Moderate

Steps

9

Time Required

                          30 minutes

Sections

3

  • Battery
  • 3 steps
  • Midframe
  • 2 steps
  • Charging Port
  • 4 steps

Flags

1

This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.

  • BackXiaomi Redmi Note

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Make sure the Xiaomi Redmi Note is powered off before removing the battery.
  • Insert the plastic opening tool between the charging port and the rear case.
  • Pry the end of the rear case up from the charging port.

Make sure the Xiaomi Redmi Note is powered off before removing the battery.

Insert the plastic opening tool between the charging port and the rear case.

Pry the end of the rear case up from the charging port.

1024

Step 2

  • Run the plastic opening tool along the seam on the side of the phone to remove the rear casing.

Run the plastic opening tool along the seam on the side of the phone to remove the rear casing.

Step 3

  • Locate the indentation at the bottom of the battery.
  • Place a finger in the indentation and lift up to remove the battery.

Locate the indentation at the bottom of the battery.

Place a finger in the indentation and lift up to remove the battery.

Step 4

              Midframe
  • Remove twelve 3.5mm Phillips #00 screws from the midframe.

Remove twelve 3.5mm Phillips #00 screws from the midframe.

Step 5

  • Insert a plastic opening into the seam between the midframe and the bottom frame of the phone.
  • Run the plastic opening tool along the seam.
  • Pry up the midframe with the plastic opening tool.
  • Once the midframe has been sufficiently lifted with the tool, place a hand underneath the edge to lift the entire component out of the frame.
  • There will be snapping sounds as the clips on the midframe disconnect from the phone.

Insert a plastic opening into the seam between the midframe and the bottom frame of the phone.

Run the plastic opening tool along the seam.

Pry up the midframe with the plastic opening tool.

Once the midframe has been sufficiently lifted with the tool, place a hand underneath the edge to lift the entire component out of the frame.

There will be snapping sounds as the clips on the midframe disconnect from the phone.

Step 6

              Charging Port
  • Locate the charging port panel at the bottom of the device.
  • Remove the 2.9 mm Phillips #00 screws on the sides of the panel.

Locate the charging port panel at the bottom of the device.

Remove the 2.9 mm Phillips #00 screws on the sides of the panel.

Step 7

  • Locate the antenna cable at the top right corner of the charging port.
  • Lift the antenna cable off of the panel with tweezers.

Locate the antenna cable at the top right corner of the charging port.

Lift the antenna cable off of the panel with tweezers.

Step 8

  • Flip the panel to its back side, but do not fully lift it off of the phone yet.
  • Use a plastic opening tool to gently pry off the press fit connector attached to the back side of the panel.

Flip the panel to its back side, but do not fully lift it off of the phone yet.

Use a plastic opening tool to gently pry off the press fit connector attached to the back side of the panel.

Step 9

  • Lift the charging port up to remove it from the frame.

Lift the charging port up to remove it from the frame.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      22 other people completed this guide.

Author

                                      with 3 other contributors 


                    Caitlin Settles

Member since: 04/26/2017

702 Reputation

                                      2 Guides authored                  



                       Badges:
                       12







                                                        +9 more badges

Team

                       Cal Poly, Team S22-G4, Livingston Spring 2017                        

                                                  Member of Cal Poly, Team S22-G4, Livingston Spring 2017 



                    CPSU-LIVINGSTON-S17S22G4                     


                                            4 Members                     


                                            16 Guides authored

Luis Amaral - Jan 24, 2018

Reply

Hi, should the battery have a certain time of charge after replacement? Or just start using like everyday, charge when needed?

ilikechocobo - Feb 25, 2018

Reply

Hi Caitlin, do you know where I can purchase an OEM Charging Port? All I can find is non OEM parts on eBay and parts on witrig. I looked into that site, and it has awful reviews, so I’m not going to try it.

Brigitte Berkaine-Tongue - Mar 12, 2018

Reply

hi where can i buy the replacement port charger for the xioami note boo pease

View similar itemsItem - Xiaomi Mi Pad 3 Tablet PC 7.9’’ MIUI 8 2.1GHz MT8176 Hexa Core 4GB+64GB WiFi

Xiaomi Mi Pad 3 Tablet PC 7.9’’ MIUI 8 2.1GHz MT8176 Hexa Core 4GB+64GB WiFi

Cynthia - Nov 2, 2018

Reply

How much is it to repair in Qatar riyal

How much does it cost to repair the charging port in Qatar royals?