Difficulty

Moderate

Steps

7

Time Required

                          15 - 25 minutes            

Sections

1

  • Rear Glass
  • 7 steps

Flags

0

  • BackXiaomi Redmi Note 8 Pro

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Before you begin this procedure, be sure to have a set of replacement adhesives for both the rear glass and the rear camera cover.

What you need

Step 1

              Heat the rear glass               
  • Prepare an iOpener and apply it to the rear glass for at least two minutes to loosen the adhesive underneath.
  • A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.

Prepare an iOpener and apply it to the rear glass for at least two minutes to loosen the adhesive underneath.

A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.

1024

Step 2

              Insert an opening pick               
  • Secure a suction handle to the bottom edge of the rear glass, as close to the edge as possible.
  • If the rear glass is cracked, the suction handle may not stick. Try lifting it with strong tape, or superglue the suction handle in place and allow it to cure so you can proceed.
  • Lift the rear glass with the suction handle to create a small gap between the rear glass and the frame.
  • In case you have trouble creating a gap, apply more heat to further soften the adhesive. Follow the iOpener instructions to avoid overheating.
  • Insert an opening pick into the gap you created.
  • Slide the opening pick to the bottom right corner to slice the adhesive.
  • Leave the opening pick in place to prevent the adhesive from resealing.

Secure a suction handle to the bottom edge of the rear glass, as close to the edge as possible.

If the rear glass is cracked, the suction handle may not stick. Try lifting it with strong tape, or superglue the suction handle in place and allow it to cure so you can proceed.

Lift the rear glass with the suction handle to create a small gap between the rear glass and the frame.

In case you have trouble creating a gap, apply more heat to further soften the adhesive. Follow the iOpener instructions to avoid overheating.

Insert an opening pick into the gap you created.

Slide the opening pick to the bottom right corner to slice the adhesive.

Leave the opening pick in place to prevent the adhesive from resealing.

Step 3

              Slice the adhesive               
  • Insert a second opening pick at the bottom edge of your phone.
  • Slide the opening pick to the bottom left corner to slice the adhesive.
  • Leave the opening picks in place to prevent the adhesive from resealing.

Insert a second opening pick at the bottom edge of your phone.

Slide the opening pick to the bottom left corner to slice the adhesive.

Leave the opening picks in place to prevent the adhesive from resealing.

Step 4

              Slice the adhesive               
  • If the adhesive becomes hard to cut, it has most likely cooled down. Use your iOpener to reheat it.
  • Insert a third opening pick at the bottom left corner of your phone.
  • Slide the opening pick along the left edge of your phone to slice the adhesive.
  • Leave the opening pick in the top left corner to prevent the adhesive from resealing.

If the adhesive becomes hard to cut, it has most likely cooled down. Use your iOpener to reheat it.

Insert a third opening pick at the bottom left corner of your phone.

Slide the opening pick along the left edge of your phone to slice the adhesive.

Leave the opening pick in the top left corner to prevent the adhesive from resealing.

Step 5

  • Insert a fourth opening pick underneath the top left corner of your phone.
  • Slide the opening pick along the top edge to slice the adhesive.
  • Leave the opening pick in the top right corner to prevent the adhesive from resealing.

Insert a fourth opening pick underneath the top left corner of your phone.

Slide the opening pick along the top edge to slice the adhesive.

Leave the opening pick in the top right corner to prevent the adhesive from resealing.

Step 6

  • Insert a fifth opening pick underneath the top right corner.
  • Slide the opening pick along the right edge of the rear glass to slice the remaining adhesive.
  • Don’t try to remove the rear glass all the way yet. The camera cover and fingerprint assembly is still adhered to its back.

Insert a fifth opening pick underneath the top right corner.

Slide the opening pick along the right edge of the rear glass to slice the remaining adhesive.

Don’t try to remove the rear glass all the way yet. The camera cover and fingerprint assembly is still adhered to its back.

Step 7

              Remove the rear glass               
  • Carefully lift to rear glass upwards whilst pressing down the camera cover with a finger.
  • The camera cover and fingerprint assembly should separate from the rear glass during this procedure. In case the adhesive is too strong, you can apply a heated iOpener to the camera cover for one to two minutes to loosen its adhesive.
  • Remove the rear glass.
  • Apply new adhesive where necessary after cleaning the relevant areas with isopropyl alcohol (>90%).
  • Secure the new rear glass with pre-cut adhesive or double-sided adhesive tape. After installing the rear glass, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond—a stack of heavy books works well.

Carefully lift to rear glass upwards whilst pressing down the camera cover with a finger.

The camera cover and fingerprint assembly should separate from the rear glass during this procedure. In case the adhesive is too strong, you can apply a heated iOpener to the camera cover for one to two minutes to loosen its adhesive.

Remove the rear glass.

Apply new adhesive where necessary after cleaning the relevant areas with isopropyl alcohol (>90%).

Secure the new rear glass with pre-cut adhesive or double-sided adhesive tape. After installing the rear glass, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond—a stack of heavy books works well.

Compare your new replacement part to the original part. You may need to transfer remaining components or remove adhesive backings from the new part before you install it.

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Cancel: I did not complete this guide.

                                                                                      6 other people completed this guide.                                             

Author

                    Dominik Schnabelrauch                     

Member since: 11/23/2016

158,135 Reputation

                                      649 Guides authored                  



                       Badges:
                       40







                                                        +37 more badges                           

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,772 Guides authored                     

Carlos Andres de la Vega - May 24, 2022

Reply

Bien explicado, gracias

miroslav.radichev - Nov 6, 2022

Reply

Had some trouble on both lower curved sides. It required a lot of pressure to keep the contact on and not lift a little. I have used a rear glass from Aliexpress so it might be the glass itself but doubt it.