Featured

Featured Guide

Difficulty

Moderate

Steps

22

Time Required

                          45 minutes - 1 hour

Sections

3

  • Rear Glass
  • 7 steps
  • How to Disconnect the Battery in the Xiaomi Redmi Note 8 Pro
  • 8 steps
  • Battery
  • 7 steps

Flags

1

This guide has been found to be exceptionally cool by the iFixit staff.

  • BackXiaomi Redmi Note 8 Pro

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

If your battery is swollen, take appropriate precautions.

For your safety, discharge your battery below 25% before disassembling your phone. This reduces the risk of a dangerous thermal event if the battery is accidentally damaged during the repair.

You’ll need replacement adhesive to reattach components when reassembling the device.

What you need

Step 1

              Heat the rear glass
  • Prepare an iOpener and apply it to the rear glass for at least two minutes to loosen the adhesive underneath.
  • A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.

Prepare an iOpener and apply it to the rear glass for at least two minutes to loosen the adhesive underneath.

A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.

1024

Step 2

              Insert an opening pick
  • Secure a suction handle to the bottom edge of the rear glass, as close to the edge as possible.
  • If the rear glass is cracked, the suction handle may not stick. Try lifting it with strong tape, or superglue the suction handle in place and allow it to cure so you can proceed.
  • Lift the rear glass with the suction handle to create a small gap between the rear glass and the frame.
  • In case you have trouble creating a gap, apply more heat to further soften the adhesive. Follow the iOpener instructions to avoid overheating.
  • Insert an opening pick into the gap you created.
  • Slide the opening pick to the bottom right corner to slice the adhesive.
  • Leave the opening pick in place to prevent the adhesive from resealing.

Secure a suction handle to the bottom edge of the rear glass, as close to the edge as possible.

If the rear glass is cracked, the suction handle may not stick. Try lifting it with strong tape, or superglue the suction handle in place and allow it to cure so you can proceed.

Lift the rear glass with the suction handle to create a small gap between the rear glass and the frame.

In case you have trouble creating a gap, apply more heat to further soften the adhesive. Follow the iOpener instructions to avoid overheating.

Insert an opening pick into the gap you created.

Slide the opening pick to the bottom right corner to slice the adhesive.

Leave the opening pick in place to prevent the adhesive from resealing.

Step 3

              Slice the adhesive
  • Insert a second opening pick at the bottom edge of your phone.
  • Slide the opening pick to the bottom left corner to slice the adhesive.
  • Leave the opening picks in place to prevent the adhesive from resealing.

Insert a second opening pick at the bottom edge of your phone.

Slide the opening pick to the bottom left corner to slice the adhesive.

Leave the opening picks in place to prevent the adhesive from resealing.

Step 4

              Slice the adhesive
  • If the adhesive becomes hard to cut, it has most likely cooled down. Use your iOpener to reheat it.
  • Insert a third opening pick at the bottom left corner of your phone.
  • Slide the opening pick along the left edge of your phone to slice the adhesive.
  • Leave the opening pick in the top left corner to prevent the adhesive from resealing.

If the adhesive becomes hard to cut, it has most likely cooled down. Use your iOpener to reheat it.

Insert a third opening pick at the bottom left corner of your phone.

Slide the opening pick along the left edge of your phone to slice the adhesive.

Leave the opening pick in the top left corner to prevent the adhesive from resealing.

Step 5

  • Insert a fourth opening pick underneath the top left corner of your phone.
  • Slide the opening pick along the top edge to slice the adhesive.
  • Leave the opening pick in the top right corner to prevent the adhesive from resealing.

Insert a fourth opening pick underneath the top left corner of your phone.

Slide the opening pick along the top edge to slice the adhesive.

Leave the opening pick in the top right corner to prevent the adhesive from resealing.

Step 6

  • Insert a fifth opening pick underneath the top right corner.
  • Slide the opening pick along the right edge of the rear glass to slice the remaining adhesive.
  • Don’t try to remove the rear glass all the way yet. The camera cover and fingerprint assembly is still adhered to its back.

Insert a fifth opening pick underneath the top right corner.

Slide the opening pick along the right edge of the rear glass to slice the remaining adhesive.

Don’t try to remove the rear glass all the way yet. The camera cover and fingerprint assembly is still adhered to its back.

Step 7

              Remove the rear glass
  • Carefully lift to rear glass upwards whilst pressing down the camera cover with a finger.
  • The camera cover and fingerprint assembly should separate from the rear glass during this procedure. In case the adhesive is too strong, you can apply a heated iOpener to the camera cover for one to two minutes to loosen its adhesive.
  • Remove the rear glass.
  • Apply new adhesive where necessary after cleaning the relevant areas with isopropyl alcohol (>90%).
  • Secure the new rear glass with pre-cut adhesive or double-sided adhesive tape. After installing the rear glass, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond—a stack of heavy books works well.

Carefully lift to rear glass upwards whilst pressing down the camera cover with a finger.

The camera cover and fingerprint assembly should separate from the rear glass during this procedure. In case the adhesive is too strong, you can apply a heated iOpener to the camera cover for one to two minutes to loosen its adhesive.

Remove the rear glass.

Apply new adhesive where necessary after cleaning the relevant areas with isopropyl alcohol (>90%).

Secure the new rear glass with pre-cut adhesive or double-sided adhesive tape. After installing the rear glass, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond—a stack of heavy books works well.

Step 8

              Pry up the fingerprint reader connector cover
  • Insert the pointed end of a spudger into the gap next to the fingerprint connector cover.
  • Use the spudger to pry up the connector cover by tilting the spudger downwards. This might require some force.

Insert the pointed end of a spudger into the gap next to the fingerprint connector cover.

Use the spudger to pry up the connector cover by tilting the spudger downwards. This might require some force.

Step 9

              Remove the fingerprint connector cover
  • Use a pair of tweezers to remove the fingerprint connector cover by pulling it out of its routing and in the direction of the power and volume buttons.

Use a pair of tweezers to remove the fingerprint connector cover by pulling it out of its routing and in the direction of the power and volume buttons.

Step 10

              Disconnect the fingerprint reader
  • Use a spudger to disconnect the fingerprint reader cable by prying the connector straight up from its socket.

Use a spudger to disconnect the fingerprint reader cable by prying the connector straight up from its socket.

Step 11

              Unfasten the motherboard cover screws
  • Use a Phillips screwdriver to remove the ten 3.9 mm-long screws securing the motherboard cover.

Use a Phillips screwdriver to remove the ten 3.9 mm-long screws securing the motherboard cover.

Step 12

              Loosen the foil
  • Slide an opening pick underneath the black foil covering the battery and interconnect cable.
  • Use the opening pick to carefully separate the black foil from the battery and the interconnect cable.

Slide an opening pick underneath the black foil covering the battery and interconnect cable.

Use the opening pick to carefully separate the black foil from the battery and the interconnect cable.

Step 13

              Pry up the motherboard cover
  • Insert the tip of an opening pick underneath the bottom right corner of the motherboard cover.
  • Slide the opening pick along the right edge of the motherboard cover to unhinge the plastic clips and pry it up.

Insert the tip of an opening pick underneath the bottom right corner of the motherboard cover.

Slide the opening pick along the right edge of the motherboard cover to unhinge the plastic clips and pry it up.

Step 14

              Remove the motherboard cover
  • Insert the opening pick underneath the top edge of the motherboard cover and pry it up.
  • Remove the motherboard cover.

Insert the opening pick underneath the top edge of the motherboard cover and pry it up.

Remove the motherboard cover.

Step 15

              Disconnect the battery cable
  • Use a spudger to disconnect the battery cable by prying the connector straight up from its socket.

Use a spudger to disconnect the battery cable by prying the connector straight up from its socket.

Step 16

              Disconnect the interconnect cable
  • Use a spudger to disconnect the interconnect cable by prying the connector straight up from its socket.

Use a spudger to disconnect the interconnect cable by prying the connector straight up from its socket.

Step 17

              Remove the black protective foil
  • Carefully slide an opening pick underneath the black foil covering the battery and the loudspeaker assembly to loosen its adhesive.
  • Remove the black protective foil.

Carefully slide an opening pick underneath the black foil covering the battery and the loudspeaker assembly to loosen its adhesive.

Remove the black protective foil.

Step 18

              Free the battery
  • During the following step do not fold the cable sharply and only bend it to avoid cable damage.
  • Fold the interconnect flex cable towards the charging port in order to get free access to both battery pull tabs.
  • You might want to use a small piece of tape to temporarily stick the cable onto your working surface to avoid accidentally damaging it during the battery removal.

During the following step do not fold the cable sharply and only bend it to avoid cable damage.

Fold the interconnect flex cable towards the charging port in order to get free access to both battery pull tabs.

You might want to use a small piece of tape to temporarily stick the cable onto your working surface to avoid accidentally damaging it during the battery removal.

Step 19

              Remove the stretch-release adhesive
  • The battery is secured to the rear case with two pieces of stretch-release adhesive.
  • Use a pair of tweezers or a clean fingernail to peel down both battery adhesive pull-tabs to un-stick them from the bottom edge of the battery.
  • Don’t jab the battery with any sharp tools. A punctured battery may leak dangerous chemicals or catch fire.

The battery is secured to the rear case with two pieces of stretch-release adhesive.

Use a pair of tweezers or a clean fingernail to peel down both battery adhesive pull-tabs to un-stick them from the bottom edge of the battery.

Don’t jab the battery with any sharp tools. A punctured battery may leak dangerous chemicals or catch fire.

Step 20

              Remove the pull-tabs
  • Grab the first pull-tab with a pair of tweezers or your fingers and slowly pull it away from the battery and towards the bottom edge of your phone.
  • Pull hard enough to maintain tension on the strip, but don’t force it. Give it plenty of time to stretch and un-stick from under the battery.
  • Don’t press down on the battery. Hold the phone firmly by its sides.
  • Keep the strip flat and unwrinkled. Try to pull evenly on the whole strip, rather than pulling mainly in the middle or on one side.
  • Pull at a low angle so the strip doesn’t snag on the edge of the battery.
  • If the adhesive strip breaks off, try to retrieve it using your fingers or blunt tweezers, and continue pulling—but do not pry under the battery.
  • If the adhesive breaks off underneath the battery and can’t be retrieved, continue with the next step.

Grab the first pull-tab with a pair of tweezers or your fingers and slowly pull it away from the battery and towards the bottom edge of your phone.

Pull hard enough to maintain tension on the strip, but don’t force it. Give it plenty of time to stretch and un-stick from under the battery.

Don’t press down on the battery. Hold the phone firmly by its sides.

Keep the strip flat and unwrinkled. Try to pull evenly on the whole strip, rather than pulling mainly in the middle or on one side.

Pull at a low angle so the strip doesn’t snag on the edge of the battery.

If the adhesive strip breaks off, try to retrieve it using your fingers or blunt tweezers, and continue pulling—but do not pry under the battery.

If the adhesive breaks off underneath the battery and can’t be retrieved, continue with the next step.

Step 21

  • Repeat the previous pull-tab removal procedure on the second pull-tab.
  • Follow the same procedure as with the previous strip: don’t press down on the battery, keep the strip flat and unwrinkled, and pull at a low angle.
  • If the adhesive breaks off underneath the battery and can’t be retrieved, apply a few drops of high concentration (over 90%) isopropyl alcohol under the edge of the battery in the area of the broken adhesive strip(s).
  • Wait about one minute for the alcohol solution to weaken the adhesive.
  • Use the flat end of a spudger to gently lift the battery.
  • Don’t try to forcefully lever the battery out. If needed, apply a few more drops of alcohol to further weaken the adhesive. Never deform or puncture the battery with your pry tool.

Repeat the previous pull-tab removal procedure on the second pull-tab.

Follow the same procedure as with the previous strip: don’t press down on the battery, keep the strip flat and unwrinkled, and pull at a low angle.

If the adhesive breaks off underneath the battery and can’t be retrieved, apply a few drops of high concentration (over 90%) isopropyl alcohol under the edge of the battery in the area of the broken adhesive strip(s).

Wait about one minute for the alcohol solution to weaken the adhesive.

Use the flat end of a spudger to gently lift the battery.

Don’t try to forcefully lever the battery out. If needed, apply a few more drops of alcohol to further weaken the adhesive. Never deform or puncture the battery with your pry tool.

Step 22

              Remove the battery
  • Remove the battery.
  • Do not reinstall a damaged or deformed battery, as doing so is a potential safety hazard.
  • If there’s any alcohol solution remaining in the phone, carefully wipe it off or allow it to air dry before installing your new battery.
  • During reassembly, temporarily reconnect the battery to the motherboard to help align it correctly. Disconnect the battery after it is seated.

Remove the battery.

Do not reinstall a damaged or deformed battery, as doing so is a potential safety hazard.

If there’s any alcohol solution remaining in the phone, carefully wipe it off or allow it to air dry before installing your new battery.

During reassembly, temporarily reconnect the battery to the motherboard to help align it correctly. Disconnect the battery after it is seated.

If possible, turn on your device and test your repair before installing new adhesive and resealing.

For optimal performance, calibrate your newly installed battery after completing this guide.

Secure the new battery with pre-cut adhesive or double-sided adhesive tape. In order to position it correctly, apply the new adhesive into the device at the places where the old adhesive was located, not directly onto the battery. Press the new battery firmly into place.

Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.

To reassemble your device, follow these instructions in reverse order. During reassembly apply new adhesive where necessary after cleaning the relevant areas with isopropyl alcohol (>90%).

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Cancel: I did not complete this guide.

                                                                                      10 other people completed this guide.

Author

                    Dominik Schnabelrauch

Member since: 11/23/2016

158,135 Reputation

                                      649 Guides authored                  



                       Badges:
                       40







                                                        +37 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,772 Guides authored