Difficulty

Moderate

Steps

15

Time Required

                          20 - 30 minutes

Sections

4

  • Opening
  • 7 steps
  • Xiaomi Redmi Note 7 Battery Disconnect
  • 3 steps
  • Fingerprint Sensor Disconnect
  • 3 steps
  • Loudspeaker
  • 2 steps

Flags

0

  • BackXiaomi Redmi Note 7

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

If you do not replace the adhesive seals when reassembling, your device will function normally, but will most likely lose its water protection.

You’ll need replacement adhesive to reattach components when reassembling the device.

What you need

Step 1

              Loosen the rear glass adhesive
  • Apply a heated iOpener to the rear glass to loosen the adhesive underneath. Apply the iOpener for at least two minutes.

Apply a heated iOpener to the rear glass to loosen the adhesive underneath. Apply the iOpener for at least two minutes.

1024

Step 2

              Insert an opening pick
  • Secure a suction handle to the bottom edge of the rear glass, as close to the edge as possible.
  • If your rear glass is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the rear glass.
  • Lift the rear glass with the suction handle to create a small gap between the glass and the frame.
  • In case you have trouble creating a gap, apply more heat to further soften the adhesive. Follow the iOpener instructions to avoid overheating.
  • Insert an opening pick into the gap.
  • Slide the opening pick to the bottom right corner to slice the adhesive.

Secure a suction handle to the bottom edge of the rear glass, as close to the edge as possible.

If your rear glass is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the rear glass.

Lift the rear glass with the suction handle to create a small gap between the glass and the frame.

In case you have trouble creating a gap, apply more heat to further soften the adhesive. Follow the iOpener instructions to avoid overheating.

Insert an opening pick into the gap.

Slide the opening pick to the bottom right corner to slice the adhesive.

Step 3

              Slice the bottom edge adhesive
  • Insert a second opening pick and slide it to the bottom left corner to slice the adhesive.
  • Leave the opening picks in place to prevent the adhesive from resealing.

Insert a second opening pick and slide it to the bottom left corner to slice the adhesive.

Leave the opening picks in place to prevent the adhesive from resealing.

Step 4

              Slice the lefthand-side adhesive
  • If the adhesive becomes hard to cut, it has most likely cooled down. Use your iOpener to reheat it.
  • Insert a third opening pick at the bottom left corner.
  • Slide the opening pick along the left edge of the phone to slice the rear glass adhesive.
  • Leave the opening pick in its place at the top left corner to prevent the adhesive from resealing.

If the adhesive becomes hard to cut, it has most likely cooled down. Use your iOpener to reheat it.

Insert a third opening pick at the bottom left corner.

Slide the opening pick along the left edge of the phone to slice the rear glass adhesive.

Leave the opening pick in its place at the top left corner to prevent the adhesive from resealing.

Step 5

              Slice the top edge adhesive
  • Insert a fourth opening pick under the top left corner of the rear glass.
  • Slide the opening pick along the top edge of the phone to slice the rear glass adhesive.
  • Leave the opening pick in the top right corner to prevent the adhesive from resealing.

Insert a fourth opening pick under the top left corner of the rear glass.

Slide the opening pick along the top edge of the phone to slice the rear glass adhesive.

Leave the opening pick in the top right corner to prevent the adhesive from resealing.

Step 6

              Slice the righthand-side adhesive
  • Insert a fifth opening pick at the top right corner of the phone.
  • Slide the opening pick along the right edge to slice the remaining adhesive.
  • Don’t try to remove the rear glass all the way yet. The fingerprint sensor is still connected to the motherboard.

Insert a fifth opening pick at the top right corner of the phone.

Slide the opening pick along the right edge to slice the remaining adhesive.

Don’t try to remove the rear glass all the way yet. The fingerprint sensor is still connected to the motherboard.

Step 7

              Open up the phone assembly
  • Carefully fold the rear glass to the left side of the phone assembly like you’d open the front cover of a book.
  • Avoid tensioning the fingerprint flex cable during this process.

Carefully fold the rear glass to the left side of the phone assembly like you’d open the front cover of a book.

Avoid tensioning the fingerprint flex cable during this process.

Step 8

              Unfasten the screws
  • Use a Phillips screw driver to remove the three 3.3 mm-long screws securing the connector cover to the midframe.

Use a Phillips screw driver to remove the three 3.3 mm-long screws securing the connector cover to the midframe.

Step 9

              Remove the connector cover
  • Use a pair of tweezers to remove the connector cover.

Use a pair of tweezers to remove the connector cover.

Step 10

              Disconnect the battery
  • Use the flat end of a spudger to pry up and disconnect the battery flex cable from the motherboard.

Use the flat end of a spudger to pry up and disconnect the battery flex cable from the motherboard.

Step 11

              Peel the protective foil off
  • For easier handling during repairs we highly recommend to separate the back cover including the fingerprint sensor from the phone assembly.
  • Use a pair of tweezers to carefully peel the yellow protective foil off the ZIF connector.

For easier handling during repairs we highly recommend to separate the back cover including the fingerprint sensor from the phone assembly.

Use a pair of tweezers to carefully peel the yellow protective foil off the ZIF connector.

Step 12

              Open the ZIF connector
  • Use the pointed end of a spudger to open the ZIF connector by bringing its black flap in an upright position.

Use the pointed end of a spudger to open the ZIF connector by bringing its black flap in an upright position.

Step 13

              Disconnect the fingerprint flex cable
  • Disconnect the fingerprint flex cable by pulling it straight out off the ZIF connector using a pair of tweezers.

Disconnect the fingerprint flex cable by pulling it straight out off the ZIF connector using a pair of tweezers.

Step 14

              Unfasten the screws
  • Use a Phillips screw driver to remove the eight 3.3 mm-long screws securing the loudspeaker assembly.

Use a Phillips screw driver to remove the eight 3.3 mm-long screws securing the loudspeaker assembly.

Step 15

              Remove the loudspeaker assembly
  • Slide an opening pick underneath the right edge of the loudspeaker assembly.
  • Use the opening pick to pry up the loudspeaker assembly.
  • Remove the loudspeaker assembly.

Slide an opening pick underneath the right edge of the loudspeaker assembly.

Use the opening pick to pry up the loudspeaker assembly.

Remove the loudspeaker assembly.

If possible, turn on your device and test your repair before installing new adhesive and resealing.

Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                    Dominik Schnabelrauch

Member since: 11/23/2016

158,135 Reputation

                                      649 Guides authored                  



                       Badges:
                       40







                                                        +37 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,772 Guides authored