Difficulty

Moderate

Steps

11

Time Required

                          10 - 20 minutes            

Sections

2

  • SIM Card Tray
  • 1 step
  • Xiaomi Redmi Note 6 Pro Opening Procedure
  • 10 steps

Flags

1

In Progress

This guide is a work in progress. Reload periodically to see the latest changes!

  • BackXiaomi Redmi Note 6 Pro

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Eject the SIM tray               
  • Insert a SIM card eject tool, a SIM eject bit, or a straightened paper clip into the hole on the SIM tray located at the left edge of the phone.
  • Press directly into the hole to eject the SIM card tray.
  • Remove the SIM card tray.

Insert a SIM card eject tool, a SIM eject bit, or a straightened paper clip into the hole on the SIM tray located at the left edge of the phone.

Press directly into the hole to eject the SIM card tray.

Remove the SIM card tray.

1024

Step 2

              Insert an opening pick               
  • The back cover is held in place by plastic clips.
  • Insert an opening pick between the screen and the back cover on the left edge of the phone where the SIM card tray was located.

The back cover is held in place by plastic clips.

Insert an opening pick between the screen and the back cover on the left edge of the phone where the SIM card tray was located.

Step 3

              Release the plastic clips               
  • Slide the opening pick along the left edge to the bottom left corner to release the plastic clips.

Slide the opening pick along the left edge to the bottom left corner to release the plastic clips.

Step 4

  • Slide the opening pick along the bottom edge to the bottom right corner to release the plastic clips.

Slide the opening pick along the bottom edge to the bottom right corner to release the plastic clips.

Step 5

  • Slide the opening pick along the right edge of your phone to the top right corner to release the plastic clips.

Slide the opening pick along the right edge of your phone to the top right corner to release the plastic clips.

Step 6

              Release the remaining plastic clips               
  • Slide the opening pick along the top edge to release the remaining plastic clips.
  • Don’t try to remove the back cover all the way yet! It’s still connected to the motherboard!

Slide the opening pick along the top edge to release the remaining plastic clips.

Don’t try to remove the back cover all the way yet! It’s still connected to the motherboard!

Step 7

              Swing open the phone assembly               
  • Carefully fold the phone assembly to the left side of the back cover like you’d open a book.

Carefully fold the phone assembly to the left side of the back cover like you’d open a book.

Step 8

              Unscrew the fingerprint cable connector cover               
  • Use a Phillips screwdriver to remove the 2.9 mm-long screw securing the fingerprint cable connector cover.

Use a Phillips screwdriver to remove the 2.9 mm-long screw securing the fingerprint cable connector cover.

Step 9

              Remove the metal cover               
  • Use a pair of blunt nose tweezers to remove the metal cover.

Use a pair of blunt nose tweezers to remove the metal cover.

Step 10

              Disconnect the fingerprint sensor               
  • Use the flat end of a spudger to disconnect the fingerprint sensor cable.

Use the flat end of a spudger to disconnect the fingerprint sensor cable.

Step 11

              Remove the back cover               
  • Remove the back cover.

Remove the back cover.

Compare your new replacement part to the original part. You may need to transfer remaining components or remove adhesive backings from the new part before you install it.

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 

                    Adriana Zwink                     

Member since: 12/18/2019

36,607 Reputation

                                      167 Guides authored                  



                       Badges:
                       34







                                                        +31 more badges                           

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,772 Guides authored