Difficulty
Moderate
Steps
18
Time Required
40 - 45 minutes
Sections
3
- Motherboard
- 11 steps
- Front Speaker
- 2 steps
- PCB Circuit Board
- 5 steps
Flags
0
BackXiaomi Redmi 2
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Motherboard
- Use the flat end of the spudger to remove the back panel from the mid-frame and front body.
Use the flat end of the spudger to remove the back panel from the mid-frame and front body.
1024
Step 2
- Insert your finger into the curved opening of the mid-frame.
- Lift the battery and remove.
Insert your finger into the curved opening of the mid-frame.
Lift the battery and remove.
Step 3
- Remove the SIM and/or memory cards if present.
- Remove twelve 3.4 mm Phillips #000 screws securing the mid-frame to the front body.
Remove the SIM and/or memory cards if present.
Remove twelve 3.4 mm Phillips #000 screws securing the mid-frame to the front body.
Step 4
- Slide the spudger between the mid-frame and front body, gradually prying the two bodies apart as you slide the spudger around the perimeter of the phone.
Slide the spudger between the mid-frame and front body, gradually prying the two bodies apart as you slide the spudger around the perimeter of the phone.
Step 5
- Remove the 3.4 mm Phillips #000 screw that holds the motherboard to the front body.
- Keep this screw separate from the initial twelve.
Remove the 3.4 mm Phillips #000 screw that holds the motherboard to the front body.
Keep this screw separate from the initial twelve.
Step 6
- Using one prong of the tweezers, pry back the brown clip located on top of the LCD ribbon connector.
Using one prong of the tweezers, pry back the brown clip located on top of the LCD ribbon connector.
Step 7
- Using one prong of the tweezers, pry the ribbon clip away from the motherboard.
Using one prong of the tweezers, pry the ribbon clip away from the motherboard.
Step 8
- Lift and hinge the motherboard with your fingers.
Lift and hinge the motherboard with your fingers.
Step 9
- Using one prong of the tweezers, lift and pry back the metal clip positioned over the front proximity sensor ribbon connector.
Using one prong of the tweezers, lift and pry back the metal clip positioned over the front proximity sensor ribbon connector.
Step 10
- Using the tweezers, pull the antenna connector from the motherboard.
Using the tweezers, pull the antenna connector from the motherboard.
Step 11
- Lift the motherboard out of the front cover and set aside.
Lift the motherboard out of the front cover and set aside.
Step 12
Front Speaker
- Using the nylon or metal spudger, gently pry the front speaker from the screen assembly.
Using the nylon or metal spudger, gently pry the front speaker from the screen assembly.
Step 13
- Using your fingers, gently lift the front speaker from the screen assembly.
Using your fingers, gently lift the front speaker from the screen assembly.
Step 14
PCB Circuit Board
- Remove the 2.9 mm Phillips #000 screw that holds the PCB circuit board to the screen assembly.
Remove the 2.9 mm Phillips #000 screw that holds the PCB circuit board to the screen assembly.
Step 15
- Using the tweezers, lift the antenna connector from the PCB circuit board.
Using the tweezers, lift the antenna connector from the PCB circuit board.
Step 16
- Do not remove the PCB circuit board at this time.
- Using the nylon or metal spudger, gently pry back the top of the PCB circuit board from the screen assembly.
Do not remove the PCB circuit board at this time.
Using the nylon or metal spudger, gently pry back the top of the PCB circuit board from the screen assembly.
Step 17
- Using the nylon or metal spudger, pry back the silver clip covering the ribbon connector.
Using the nylon or metal spudger, pry back the silver clip covering the ribbon connector.
Step 18
- Carefully lift the PCB circuit board from the screen assembly and set aside.
- The screen assembly is pictured to the left of the circuit board and is now ready for repair or replacement.
Carefully lift the PCB circuit board from the screen assembly and set aside.
The screen assembly is pictured to the left of the circuit board and is now ready for repair or replacement.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
31 other people completed this guide.
Author
with 2 other contributors
Alicia Brenner
Member since: 10/01/2015
3,509 Reputation
5 Guides authored
Badges:
14
+11 more badges
Team
USF Tampa, Team 1-3, Leahy Fall 2015
Member of USF Tampa, Team 1-3, Leahy Fall 2015
USFT-LEAHY-F15S1G3
2 Members
5 Guides authored
SAFUTRA - Apr 17, 2016
Reply
ok so good is can service nice
Rajesh Gopisetti - Feb 9, 2017
Reply
Touch is not working after replacing full LCD, Brought new display & changed again but no luck, Display is okay but touch not working.