Difficulty

Moderate

Steps

7

Time Required

                          30 minutes

Sections

2

  • Battery
  • 4 steps
  • Micro USB/Microphone/Virtual Keys light/Vibrator
  • 3 steps

Flags

1

Incorrect Tools

Help make this guide better by using the correct tools in images and/or text.

  • BackXiaomi Mi Note

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Use your suction cup to grip the back of the phone. Once the suction cup is secure, pull back with moderate force and the back plate should snap free.

Use your suction cup to grip the back of the phone. Once the suction cup is secure, pull back with moderate force and the back plate should snap free.

1024

Step 2

  • Once the back plate is off you will need to detach the frames that hold in the battery. Locate and remove the screws (Screws are marked in the image). You can then pull the frame off with ease once the screws have been removed.
  • Remove the six 3.5mm Phillips #000 black screws using a securing part of the back panels.
  • Remove the seven 2.5mm Phillips #000 black screws securing part of the back panels.
  • Remove the five 2mm Phillips #000 silver screws securing the remaining back panels.

Once the back plate is off you will need to detach the frames that hold in the battery. Locate and remove the screws (Screws are marked in the image). You can then pull the frame off with ease once the screws have been removed.

Remove the six 3.5mm Phillips #000 black screws using a securing part of the back panels.

Remove the seven 2.5mm Phillips #000 black screws securing part of the back panels.

Remove the five 2mm Phillips #000 silver screws securing the remaining back panels.

Step 3

  • Use a nylon spudger to pry upwards to detach the ribbon that’s connecting the battery to the motherboard.

Use a nylon spudger to pry upwards to detach the ribbon that’s connecting the battery to the motherboard.

Step 4

  • Insert a nylon or metal spudger underneath the battery at any point. Then slide the spudger around all the edges to loosen it. The battery can now be easily lifted out of the frame.
  • Glue will be holding down the backside of the battery.

Insert a nylon or metal spudger underneath the battery at any point. Then slide the spudger around all the edges to loosen it. The battery can now be easily lifted out of the frame.

Glue will be holding down the backside of the battery.

Step 5

              Micro USB/Microphone/Virtual Keys light/Vibrator
  • Use tweezers to pull upwards and detach the microphone wire that connects the motherboard to the dock connector.

Use tweezers to pull upwards and detach the microphone wire that connects the motherboard to the dock connector.

Step 6

  • Peel back the ribbon that is adhered to the metal surface as shown.

Peel back the ribbon that is adhered to the metal surface as shown.

Step 7

  • The dock connector is firmly adhered to the frame below it. To prevent damage to the phone use minimal force when removing.
  • Using tweezers slowly start prying upwards at the locations shown in the images. After carefully prying around the edges of the dock connector, it can now lifted upwards out of the frame.

The dock connector is firmly adhered to the frame below it. To prevent damage to the phone use minimal force when removing.

Using tweezers slowly start prying upwards at the locations shown in the images. After carefully prying around the edges of the dock connector, it can now lifted upwards out of the frame.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      9 other people completed this guide.

Author

                                      with 4 other contributors 


                    Mark Sears

Member since: 08/27/2015

1,195 Reputation

                                      4 Guides authored                  



                       Badges:
                       12







                                                        +9 more badges

Team

                       USF Tampa, Team 1-6, Sullivan Fall 2015                        

                                                  Member of USF Tampa, Team 1-6, Sullivan Fall 2015 



                    USFT-SULLIVAN-F15S1G6                     


                                            4 Members                     


                                            6 Guides authored

Christophe C - May 9, 2017

Reply

Très difficile de retirer le pcb avec le prise mini USB et impossible de des souder directement bien sur. Le buzzer est justement mal placé et gène horriblement. Environ 1h pose/dépose.