Difficulty
Moderate
Steps
20
Time Required
45 minutes - 1 hour
Sections
4
- Rear Glass
- 8 steps
- Xiaomi Mi 10 Motherboard Cover & Charging Coil Removal
- 8 steps
- Xiaomi Mi 10 Battery Disconnect
- 1 step
- Upper Loudspeaker
- 3 steps
Flags
0
BackXiaomi Mi 10
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
You’ll need replacement adhesive to reattach components when reassembling the device.
What you need
Step 1
Heat the rear glass
- Before you begin, switch off your phone.
- Apply a heated iOpener to the back of the phone to loosen the adhesive beneath the back cover. Apply the iOpener for at least two minutes.
Before you begin, switch off your phone.
Apply a heated iOpener to the back of the phone to loosen the adhesive beneath the back cover. Apply the iOpener for at least two minutes.
1024
Step 2
Insert the iFlex
- Secure a suction handle to the bottom of the rear glass, as close to the edge as possible.
- If the phone’s rear glass is cracked, the suction handle may not stick. Try lifting it with strong tape, or superglue the suction handle in place and allow it to cure so you can proceed.
- Lift the rear glass with the suction handle to create a small gap between the glass and the frame.
- The rear glass of the Xiaomi Mi 10 sits tightly in place. In order to create a gap that is big enough to insert an opening pick, you need to insert an iFlex first.
- Insert the iFlex into the gap and leave it in place to prevent the adhesive from resealing.
Secure a suction handle to the bottom of the rear glass, as close to the edge as possible.
If the phone’s rear glass is cracked, the suction handle may not stick. Try lifting it with strong tape, or superglue the suction handle in place and allow it to cure so you can proceed.
Lift the rear glass with the suction handle to create a small gap between the glass and the frame.
The rear glass of the Xiaomi Mi 10 sits tightly in place. In order to create a gap that is big enough to insert an opening pick, you need to insert an iFlex first.
Insert the iFlex into the gap and leave it in place to prevent the adhesive from resealing.
Step 3
Begin to slice the adhesive
- Insert an opening pick into the gap you created with the iFlex.
- Slide the opening pick to the bottom right corner.
- At this point you can remove the iFlex from the phone.
Insert an opening pick into the gap you created with the iFlex.
Slide the opening pick to the bottom right corner.
At this point you can remove the iFlex from the phone.
Step 4
Slice the bottom edge adhesive
- Insert a second opening pick and slide it to the bottom left corner to cut the adhesive.
- Leave the opening picks in place to prevent the adhesive from resealing.
Insert a second opening pick and slide it to the bottom left corner to cut the adhesive.
Leave the opening picks in place to prevent the adhesive from resealing.
Step 5
Slice the lefthand-side adhesive
- Insert a third opening pick at the bottom left corner.
- Slide the tip of the opening pick from the bottom left corner along the side of the phone to cut the adhesive.
- Leave the opening pick in its place at the top left corner to prevent the adhesive from resealing.
Insert a third opening pick at the bottom left corner.
Slide the tip of the opening pick from the bottom left corner along the side of the phone to cut the adhesive.
Leave the opening pick in its place at the top left corner to prevent the adhesive from resealing.
Step 6
Slice the top edge adhesive
- If the adhesive becomes hard to cut, it has most likely cooled down. Use your iOpener to reheat it.
- Insert a fourth opening pick under the top left corner of the rear glass.
- Slide the opening pick along the top edge of the phone to cut the adhesive.
- Leave the opening pick in the top right corner to prevent the adhesive from resealing.
If the adhesive becomes hard to cut, it has most likely cooled down. Use your iOpener to reheat it.
Insert a fourth opening pick under the top left corner of the rear glass.
Slide the opening pick along the top edge of the phone to cut the adhesive.
Leave the opening pick in the top right corner to prevent the adhesive from resealing.
Step 7
Slice the righthand-side adhesive
- Insert a fifth opening pick at the top right corner of the phone.
- Slide the opening pick along the right side to cut the remaining adhesive.
Insert a fifth opening pick at the top right corner of the phone.
Slide the opening pick along the right side to cut the remaining adhesive.
Step 8
Remove the rear glass
- Remove the rear glass.
- During reassembly, this is a good point to power on your phone and test all functions before sealing it up. Be sure to power your phone back down completely before you continue working.
Remove the rear glass.
During reassembly, this is a good point to power on your phone and test all functions before sealing it up. Be sure to power your phone back down completely before you continue working.
Step 9
Unfasten the screws
- Remove the four 4.9 mm Phillips #00 screws.
Remove the four 4.9 mm Phillips #00 screws.
Step 10
Loosen the charging coil adhesive
- Use an opening pick to slice the adhesive underneath the black protective mat covering the upper loudspeaker assembly.
Use an opening pick to slice the adhesive underneath the black protective mat covering the upper loudspeaker assembly.
Step 11
Loosen the bottom adhesive
- Use an opening pick to slice the adhesive underneath the black protective mat covering the bottom loudspeaker assembly.
Use an opening pick to slice the adhesive underneath the black protective mat covering the bottom loudspeaker assembly.
Step 12
Loosen the NFC & charging coil assembly
- There is a small piece of protective copper foil underneath the NFC and charging coil assembly. Avoid damaging it during the following procedure.
- Slide a plastic card or playing card underneath the NFC and charging coil assembly.
- Use the card to carefully loosen the adhesive underneath the left edge of the assembly.
- To make this process easier, you can apply a heated iOpener to the left edge of the NFC and charging coil assembly to soften the adhesive.
- Do not remove the NFC and charging coil assembly all the way yet. It is still glued to the motherboard cover.
There is a small piece of protective copper foil underneath the NFC and charging coil assembly. Avoid damaging it during the following procedure.
Slide a plastic card or playing card underneath the NFC and charging coil assembly.
Use the card to carefully loosen the adhesive underneath the left edge of the assembly.
To make this process easier, you can apply a heated iOpener to the left edge of the NFC and charging coil assembly to soften the adhesive.
Do not remove the NFC and charging coil assembly all the way yet. It is still glued to the motherboard cover.
Step 13
Fold over the NFC & charging coil assembly
- Carefully fold the NFC & charging coil assembly to the left side of the phone.
Carefully fold the NFC & charging coil assembly to the left side of the phone.
Step 14
Unfasten the screws
- Remove the five 4.9 mm Phillips #00 screws.
Remove the five 4.9 mm Phillips #00 screws.
Step 15
Pry up the motherboard cover
- Slide an opening pick underneath the bottom right edge of the motherboard cover.
- Use the opening pick to pry up the motherboard cover.
Slide an opening pick underneath the bottom right edge of the motherboard cover.
Use the opening pick to pry up the motherboard cover.
Step 16
Remove the motherboard cover
- Remove the motherboard cover including the NFC and charging coil assembly.
Remove the motherboard cover including the NFC and charging coil assembly.
Step 17
Disconnect the battery
- Use the flat end of a spudger to pry up and disconnect the battery flex cable.
Use the flat end of a spudger to pry up and disconnect the battery flex cable.
Step 18
Unfasten the screws
- Remove the three Phillips #00 screws securing the upper loudspeaker assembly.
Remove the three Phillips #00 screws securing the upper loudspeaker assembly.
Step 19
Pry up the loudspeaker assembly
- Insert an opening pick underneath the bottom left edge of the upper loudspeaker assembly.
- Use the opening pick to pry up the loudspeaker assembly.
Insert an opening pick underneath the bottom left edge of the upper loudspeaker assembly.
Use the opening pick to pry up the loudspeaker assembly.
Step 20
Remove the loudspeaker
- Remove the upper loudspeaker assembly.
Remove the upper loudspeaker assembly.
To reassemble your device, follow these instructions in reverse order.
Take your e-waste to an R2 or e-Stewards certified recycler.
Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 1 other contributor
Dominik Schnabelrauch
Member since: 11/23/2016
158,135 Reputation
649 Guides authored
Badges:
40
+37 more badges
Team
iFixit
Member of iFixit
Community
141 Members
15,772 Guides authored