Xbox One X Project Scorpio Edition Outer Case Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          25 minutes

Sections

Outer Case
9 steps

Flags

BackXbox One X Project Scorpio Edition
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Outer Case

Use a T9 Torx screwdriver to remove the 13mm screw which is under and to the left of the power input.

Use a T9 Torx screwdriver to remove the 13mm screw which is under and to the left of the power input.

1024

Step 2

Using precision tweezers, remove the screw tab located on opposite side of the box.
Use a T9 Torx screwdriver to remove the 13mm screw revealed underneath the tab.

Using precision tweezers, remove the screw tab located on opposite side of the box.

Use a T9 Torx screwdriver to remove the 13mm screw revealed underneath the tab.

Step 3

Orient the case so that the front of the Xbox (the side with the power button) is facing you.
Remove the top of the case by sliding the case towards you.

Orient the case so that the front of the Xbox (the side with the power button) is facing you.

Remove the top of the case by sliding the case towards you.

Step 4

Using a T9 Torx screwdriver, remove the two 15mm silver screws that are holding a circuit board/panel to the side of the interior metal casing.
Using the same screwdriver, remove the 9mm black screw located farther to the right on the same circuit board/panel.

Using a T9 Torx screwdriver, remove the two 15mm silver screws that are holding a circuit board/panel to the side of the interior metal casing.

Using the same screwdriver, remove the 9mm black screw located farther to the right on the same circuit board/panel.

Step 5

Remove the unscrewed panel from the side of the device by pulling it toward you.
Be mindful of the connector, as it is fragile.

Remove the unscrewed panel from the side of the device by pulling it toward you.

Be mindful of the connector, as it is fragile.

Step 6

Pull the upper edge of the white clip down, and then remove the white connector from the dislocated panel using precision tweezers.
Do not force the connector out, as it is fragile. Wiggling may be necessary.

Pull the upper edge of the white clip down, and then remove the white connector from the dislocated panel using precision tweezers.

Do not force the connector out, as it is fragile. Wiggling may be necessary.

Step 7

On the top of the device in the corner directly above the white connector, there is an oval plate held in place by two screws.
Remove both of these 7mm screws with a Torx T9 screwdriver.
Lift the detached plate off to the side.
The plate is still connected to the device.

On the top of the device in the corner directly above the white connector, there is an oval plate held in place by two screws.

Remove both of these 7mm screws with a Torx T9 screwdriver.

Lift the detached plate off to the side.

The plate is still connected to the device.

Step 8

Use a Torx T9 screwdriver to remove the six 47mm long screws, which attach the bottom side of the outer case.

Use a Torx T9 screwdriver to remove the six 47mm long screws, which attach the bottom side of the outer case.

Step 9

Turn the Xbox over, so that the bottom of the case is on top.
Lift the bottom of the case off of the Xbox by pulling it up and toward you.

Turn the Xbox over, so that the bottom of the case is on top.

Lift the bottom of the case off of the Xbox by pulling it up and toward you.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      7 other people completed this guide.

Author

                                      with 4 other contributors

                    Ashley Masuda

Member since: 01/24/2018

2,623 Reputation

                                      7 Guides authored                  



                       Badges:
                       19







                                                        +16 more badges

Team

                       Cal Poly, Team S2-G6, Livingston Winter 2018                        

                                                  Member of Cal Poly, Team S2-G6, Livingston Winter 2018 



                    CPSU-LIVINGSTON-W18S2G6                     


                                            4 Members                     


                                            23 Guides authored

Daniel - Oct 3, 2018

Where do you get the outer case from? And if I only want to replace the outer case could I just follow the first 3 steps?

Introduction#

What you need#

Team#

Introduction

What you need

Team