Difficulty
Moderate
Steps
14
Time Required
30 minutes
Sections
2
- Outer Case
- 9 steps
- BD-ROM Drive
- 5 steps
Flags
0
BackXbox One X Project Scorpio Edition
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Outer Case
- Use a T9 Torx screwdriver to remove the 13mm screw which is under and to the left of the power input.
Use a T9 Torx screwdriver to remove the 13mm screw which is under and to the left of the power input.
1024
Step 2
- Using precision tweezers, remove the screw tab located on opposite side of the box.
- Use a T9 Torx screwdriver to remove the 13mm screw revealed underneath the tab.
Using precision tweezers, remove the screw tab located on opposite side of the box.
Use a T9 Torx screwdriver to remove the 13mm screw revealed underneath the tab.
Step 3
- Orient the case so that the front of the Xbox (the side with the power button) is facing you.
- Remove the top of the case by sliding the case towards you.
Orient the case so that the front of the Xbox (the side with the power button) is facing you.
Remove the top of the case by sliding the case towards you.
Step 4
- Using a T9 Torx screwdriver, remove the two 15mm silver screws that are holding a circuit board/panel to the side of the interior metal casing.
- Using the same screwdriver, remove the 9mm black screw located farther to the right on the same circuit board/panel.
Using a T9 Torx screwdriver, remove the two 15mm silver screws that are holding a circuit board/panel to the side of the interior metal casing.
Using the same screwdriver, remove the 9mm black screw located farther to the right on the same circuit board/panel.
Step 5
- Remove the unscrewed panel from the side of the device by pulling it toward you.
- Be mindful of the connector, as it is fragile.
Remove the unscrewed panel from the side of the device by pulling it toward you.
Be mindful of the connector, as it is fragile.
Step 6
- Pull the upper edge of the white clip down, and then remove the white connector from the dislocated panel using precision tweezers.
- Do not force the connector out, as it is fragile. Wiggling may be necessary.
Pull the upper edge of the white clip down, and then remove the white connector from the dislocated panel using precision tweezers.
Do not force the connector out, as it is fragile. Wiggling may be necessary.
Step 7
- On the top of the device in the corner directly above the white connector, there is an oval plate held in place by two screws.
- Remove both of these 7mm screws with a Torx T9 screwdriver.
- Lift the detached plate off to the side.
- The plate is still connected to the device.
On the top of the device in the corner directly above the white connector, there is an oval plate held in place by two screws.
Remove both of these 7mm screws with a Torx T9 screwdriver.
Lift the detached plate off to the side.
The plate is still connected to the device.
Step 8
- Use a Torx T9 screwdriver to remove the six 47mm long screws, which attach the bottom side of the outer case.
Use a Torx T9 screwdriver to remove the six 47mm long screws, which attach the bottom side of the outer case.
Step 9
- Turn the Xbox over, so that the bottom of the case is on top.
- Lift the bottom of the case off of the Xbox by pulling it up and toward you.
Turn the Xbox over, so that the bottom of the case is on top.
Lift the bottom of the case off of the Xbox by pulling it up and toward you.
Step 10
BD-ROM Drive
- Flip over the device again, so that the top is facing upwards.
- Remove the 4 smaller 11mm screws in the lower left corner on the metal casing using a Torx T9 screwdriver.
Flip over the device again, so that the top is facing upwards.
Remove the 4 smaller 11mm screws in the lower left corner on the metal casing using a Torx T9 screwdriver.
Step 11
- Flip over the device again, so that the bottom is facing upwards.
- Using a Torx T10 screwdriver, remove the two screws located on opposite sides of the metal casing. One is near the fan vent, and the other is near the power supply vent.
- The left screw is 11mm and the right screw is 7.5 mm.
Flip over the device again, so that the bottom is facing upwards.
Using a Torx T10 screwdriver, remove the two screws located on opposite sides of the metal casing. One is near the fan vent, and the other is near the power supply vent.
The left screw is 11mm and the right screw is 7.5 mm.
Step 12
- Remove the metal casing by pulling it upward, revealing the interior components of the device.
Remove the metal casing by pulling it upward, revealing the interior components of the device.
Step 13
- Lift and rotate the BD drive to reveal the wires that connect it to the motherboard.
Lift and rotate the BD drive to reveal the wires that connect it to the motherboard.
Step 14
- Using your fingers, gently unplug the two sets of wires connecting the drive to the motherboard.
- Alternatively, you can disconnect the wires from the drive-side sockets. This is much easier if you have not removed the power supply.
- The BD drive should now be completely detached from the rest of the device, and it can be set aside.
Using your fingers, gently unplug the two sets of wires connecting the drive to the motherboard.
Alternatively, you can disconnect the wires from the drive-side sockets. This is much easier if you have not removed the power supply.
The BD drive should now be completely detached from the rest of the device, and it can be set aside.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
4 other people completed this guide.
Author
with 6 other contributors
Ashley Masuda
Member since: 01/24/2018
2,623 Reputation
7 Guides authored
Badges:
19
+16 more badges
Team
Cal Poly, Team S2-G6, Livingston Winter 2018
Member of Cal Poly, Team S2-G6, Livingston Winter 2018
CPSU-LIVINGSTON-W18S2G6
4 Members
23 Guides authored
Chris Storey - Mar 26, 2019
Reply
ok it says no other parts required besides the tweezers and the t9 screw driver, but it doesn’t mention what model of BD-ROM is suitable to replace it with.
mthouchen - Jun 9, 2019
Reply
The six long screws actually take a T-10 bit
Marcel - Jun 15, 2019
Reply
Please FIX Number 8 THIS IS NOT RIGHT!
Unfortunately the manual is not correct here. Above the black slot is a white switch / pen, fold it over with your fingernail, so fold it over to the front. Then the cable can be easily removed without any problems and tweezers. GERMAN: Hier ist die Anleitung leider nicht korrekt. Oberhalb des schwarzen Steckplatzes befindet sich ein weißer Schalter/Stift, diesen mit dem Fingernagel umklappen, also praktisch zu der Vorderseite umklappen. Danach lässt sich das Kabel ohne Probleme und Pinzette einfach abziehen.
Robb Applebee - Nov 13, 2019
Reply
What is the model of the BD ROM drive for the xBox 1 X?
soorajlal - Apr 9, 2020
Reply
Followed this guide and https://www.youtube.com/watch?v=wO-QanKR… and upgraded my Xbox One X Project Scorpio edition to 2TB SSD. Thanks and keep up the good work