Difficulty

Difficult

Steps

7

Time Required

                          40 - 45 minutes            

Sections

2

  • Bumpers
  • 5 steps
  • Rumble Motor
  • 2 steps

Flags

0

  • BackXbox One Wireless Controller (Model 1697)

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Bumpers               
  • Remove the battery pack cover.
  • Remove the two AA batteries.
  • Carefully remove the sticker or puncture to reveal the screw.

Remove the battery pack cover.

Remove the two AA batteries.

Carefully remove the sticker or puncture to reveal the screw.

1024

Step 2

  • Remove the side handles by wedging the spudger around the side panels.
  • Pry the side panel by moving the spudger back and forth. You must do this along the entire seam to remove the side handle panel.
  • There are seven clips that need to be opened to remove each handle panel.

Remove the side handles by wedging the spudger around the side panels.

Pry the side panel by moving the spudger back and forth. You must do this along the entire seam to remove the side handle panel.

There are seven clips that need to be opened to remove each handle panel.

Step 3

  • Removing the side handles allows access to remove the faceplate.
  • Use the TORX TR8 screwdriver to remove the five TR9 Torx screws.

Removing the side handles allows access to remove the faceplate.

Use the TORX TR8 screwdriver to remove the five TR9 Torx screws.

Step 4

  • Now that the bumpers are easily visible make sure to clean any dirt or grime that may be around the bumpers.
  • The bumpers are connected by a middle plastic cover that is around the Xbox home button. Remove this plastic piece by lifting the plastic cover over the two pins, pressing the home button in, and pushing the cover towards the top of the controller.
  • Be aware of the sync button loosely placed under the plastic covering. Ensure it is put back before putting back the bumper/plastic cover assembly.
  • Remove the current bumper assembly by pulling them off the plastic cover.

Now that the bumpers are easily visible make sure to clean any dirt or grime that may be around the bumpers.

The bumpers are connected by a middle plastic cover that is around the Xbox home button. Remove this plastic piece by lifting the plastic cover over the two pins, pressing the home button in, and pushing the cover towards the top of the controller.

Be aware of the sync button loosely placed under the plastic covering. Ensure it is put back before putting back the bumper/plastic cover assembly.

Remove the current bumper assembly by pulling them off the plastic cover.

Step 5

  • The controller is now ready for the new bumper assembly.
  • Align the new bumpers onto the top of the controller by holding down the triggers and aligning the four pins on both sides.
  • Set the new home button cover over the micro USB port, push the home button in, and pull the cover over the two pins shown.

The controller is now ready for the new bumper assembly.

Align the new bumpers onto the top of the controller by holding down the triggers and aligning the four pins on both sides.

Set the new home button cover over the micro USB port, push the home button in, and pull the cover over the two pins shown.

Step 6

              Rumble Motor               
  • De-solder the soldered joints while holding the red and black wires down on the top motherboard.
  • Use the How to Solder and Desolder Connections guide on iFixit to correctly (de)solder the components in your device.
  • Use caution while using the soldering iron so you don’t damage other components or hurt yourself.

De-solder the soldered joints while holding the red and black wires down on the top motherboard.

Use the How to Solder and Desolder Connections guide on iFixit to correctly (de)solder the components in your device.

Use caution while using the soldering iron so you don’t damage other components or hurt yourself.

Step 7

  • Remove the rumble motors.

Remove the rumble motors.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      6 other people completed this guide.                                             

Author

                                      with 3 other contributors 

                    Ryan Burroughs                     

Member since: 09/25/2017

1,132 Reputation

                                      2 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges                           

Team

                       USF Tampa, Team S9-G1, Remmell Fall 2017                        

                                                  Member of USF Tampa, Team S9-G1, Remmell Fall 2017 



                    USFT-REMMELL-F17S9G1                     


                                            4 Members                     


                                            12 Guides authored