Xbox One Stereo Headset Circuit Board Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          5 - 10 minutes

Sections

Adapter Circuit Board
5 steps

Flags

BackXbox One Stereo Headset
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Adapter Circuit Board

Insert the flat edge of a metal spudger in the seam between the adapter body and the plastic casing. Move the spudger into one of the corners.
Push down on the spudger to separate the casing from the adapter until you hear a click and the casing stays open on that side.
Do the same to the other side until the casing comes off.
When reassembling, first align the headphone jack in the back of the adapter body with the hole in the casing, then align the tabs on the floor of the casing with the holes in the bottom of the adapter body.

Insert the flat edge of a metal spudger in the seam between the adapter body and the plastic casing. Move the spudger into one of the corners.

Push down on the spudger to separate the casing from the adapter until you hear a click and the casing stays open on that side.

Do the same to the other side until the casing comes off.

When reassembling, first align the headphone jack in the back of the adapter body with the hole in the casing, then align the tabs on the floor of the casing with the holes in the bottom of the adapter body.

1024

Step 2

Remove three 5.0 mm T5 Security Torx screws along the edges of the controller housing.
Remove two 8.0 mm T5 Security Torx screws near the top-center of the adapter.

Remove three 5.0 mm T5 Security Torx screws along the edges of the controller housing.

Remove two 8.0 mm T5 Security Torx screws near the top-center of the adapter.

Step 3

With your fingers, carefully lift the adapter housing from the button panel.
Be careful not to yank the wires connecting the two halves of the circuit board.

With your fingers, carefully lift the adapter housing from the button panel.

Be careful not to yank the wires connecting the two halves of the circuit board.

Step 4

Pull back on the controller USB connector with your interview to separate the main adapter circuit board from the rubber mold in the button panel.

Pull back on the controller USB connector with your interview to separate the main adapter circuit board from the rubber mold in the button panel.

Step 5

Remove the two 5.5 mm Phillips #00 screws connecting the smaller circuit board to the adapter housing. The smaller circuit board should come right off.
One of the screws is located beneath the connecting wires, so you may have to move the main circuit board around until you can see the screw.

Remove the two 5.5 mm Phillips #00 screws connecting the smaller circuit board to the adapter housing. The smaller circuit board should come right off.

One of the screws is located beneath the connecting wires, so you may have to move the main circuit board around until you can see the screw.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      7 other people completed this guide.

Author

                                      with 3 other contributors

                    Justin Rosescu

Member since: 01/30/2015

500 Reputation

                                      2 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       Cal Poly, Team 17-37, Amido Winter 2015                        

                                                  Member of Cal Poly, Team 17-37, Amido Winter 2015 



                    CPSU-AMIDO-W15S17G37                     


                                            4 Members                     


                                            5 Guides authored

Ramesh Sirdar - Sep 29, 2015

Where do i get the circuit board to buy ?

Laurschanny - Mar 3, 2016

Thank you, I opened the adapter in minutes, which is all I wanted to do.

Introduction#

What you need#

Team#

Introduction

What you need

Team