Difficulty
Moderate
Steps
16
Time Required
45 minutes - 1 hour
Sections
6
- Plastic Enclosure
- 4 steps
- Top Metal Shield
- 2 steps
- Wifi Card
- 2 steps
- IR Blaster
- 2 steps
- Bottom Metal Shield
- 3 steps
- Power Supply
- 3 steps
Flags
0
BackXbox One S All Digital Edition
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Plastic Enclosure
- Position the iFixit Opening Tool’s riveted edge in between the top and bottom cover of the plastic enclosure.
- Apply downward pressure on the iFixit Opening Tool until the security clip unlocks.
- Repeat on different points of the plastic enclosure until the bottom cover is removed.
Position the iFixit Opening Tool’s riveted edge in between the top and bottom cover of the plastic enclosure.
Apply downward pressure on the iFixit Opening Tool until the security clip unlocks.
Repeat on different points of the plastic enclosure until the bottom cover is removed.
1024
Step 2
- Remove the six 50 mm green screws (labeled F1-F6) from the metal chassis using a Torx 10 screwdriver.
- These screws hold the top cover of the plastic enclosure to the chassis.
Remove the six 50 mm green screws (labeled F1-F6) from the metal chassis using a Torx 10 screwdriver.
These screws hold the top cover of the plastic enclosure to the chassis.
Step 3
- Apply pressure to peel off the sides of the casing.
- Separate the metal chassis from the top cover, lifting the back of the chassis up and away from the top cover.
- The plastic back panel is meant to stay attached to the metal chassis.
Apply pressure to peel off the sides of the casing.
Separate the metal chassis from the top cover, lifting the back of the chassis up and away from the top cover.
The plastic back panel is meant to stay attached to the metal chassis.
Step 4
- Flip the metal enclosure so that the fan cover is on top.
Flip the metal enclosure so that the fan cover is on top.
Step 5
Top Metal Shield
- Remove the two 15mm screws from the front panel using the Torx T8 screwdriver.
Remove the two 15mm screws from the front panel using the Torx T8 screwdriver.
Step 6
- Carefully slide the top metal case off the frame.
- This may require shifting the case side to side as you slide up.
Carefully slide the top metal case off the frame.
This may require shifting the case side to side as you slide up.
Step 7
Wifi Card
- Remove the three 15 mm screws with the Torx T8 Security Bit Screwdriver.
- The top of the metal chassis has been removed in the picture, but is not necessary for the replacement.
Remove the three 15 mm screws with the Torx T8 Security Bit Screwdriver.
The top of the metal chassis has been removed in the picture, but is not necessary for the replacement.
Step 8
- Carefully remove the WiFi Card from the metal chassis.
Carefully remove the WiFi Card from the metal chassis.
Step 9
IR Blaster
- Remove the four 15mm screws attaching the IR Blaster to the metal chassis with the Torx T8 Security screwdriver.
Remove the four 15mm screws attaching the IR Blaster to the metal chassis with the Torx T8 Security screwdriver.
Step 10
- Carefully remove the IR Blaster from the metal chassis.
- The connector is very fragile. Make sure you pull the board away from the case and not sideways.
Carefully remove the IR Blaster from the metal chassis.
The connector is very fragile. Make sure you pull the board away from the case and not sideways.
Step 11
Bottom Metal Shield
- Remove the eight 10mm screws from the bottom of the metal casing using the Torx T9 screwdriver.
- Remove the four 15mm screws from the bottom of the heatsink fastener using the Torx T8 screwdriver.
Remove the eight 10mm screws from the bottom of the metal casing using the Torx T9 screwdriver.
Remove the four 15mm screws from the bottom of the heatsink fastener using the Torx T8 screwdriver.
Step 12
- Remove the two plastic pieces from the motherboard.
Remove the two plastic pieces from the motherboard.
Step 13
- Lift the motherboard up from the metal chassis.
- The motherboard should easily separate from the metal chassis.
Lift the motherboard up from the metal chassis.
The motherboard should easily separate from the metal chassis.
Step 14
Power Supply
- Gently lift the hard drive to free up some space around the power supply.
Gently lift the hard drive to free up some space around the power supply.
Step 15
- Lift the power supply up and away from the motherboard.
Lift the power supply up and away from the motherboard.
Step 16
- Disconnect the six pin connector from the motherboard.
Disconnect the six pin connector from the motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 3 other contributors
Jules Hajjar
Member since: 10/10/2019
1,372 Reputation
8 Guides authored
Badges:
16
+13 more badges
Team
Cal Poly, Team S12-G6, Regan Fall 2019
Member of Cal Poly, Team S12-G6, Regan Fall 2019
CPSU-REGAN-F19S12G6
4 Members
24 Guides authored
William Oliver - Oct 19, 2021
Reply
I replaced the power supply and my Xbox still isn’t turning on. I used a power supply I got from this website. Please help
Jules Hajjar - Dec 13, 2021
Another issue could be the power button on the front power board. If possible, you could try to replace that as well.
