Difficulty
Moderate
Steps
9
Time Required
20 - 40 minutes
Sections
3
- Plastic Enclosure
- 4 steps
- Top Metal Shield
- 2 steps
- Bottom Metal Shield
- 3 steps
Flags
0
BackXbox One S All Digital Edition
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Plastic Enclosure
- Position the iFixit Opening Tool’s riveted edge in between the top and bottom cover of the plastic enclosure.
- Apply downward pressure on the iFixit Opening Tool until the security clip unlocks.
- Repeat on different points of the plastic enclosure until the bottom cover is removed.
Position the iFixit Opening Tool’s riveted edge in between the top and bottom cover of the plastic enclosure.
Apply downward pressure on the iFixit Opening Tool until the security clip unlocks.
Repeat on different points of the plastic enclosure until the bottom cover is removed.
1024
Step 2
- Remove the six 50 mm green screws (labeled F1-F6) from the metal chassis using a Torx 10 screwdriver.
- These screws hold the top cover of the plastic enclosure to the chassis.
Remove the six 50 mm green screws (labeled F1-F6) from the metal chassis using a Torx 10 screwdriver.
These screws hold the top cover of the plastic enclosure to the chassis.
Step 3
- Apply pressure to peel off the sides of the casing.
- Separate the metal chassis from the top cover, lifting the back of the chassis up and away from the top cover.
- The plastic back panel is meant to stay attached to the metal chassis.
Apply pressure to peel off the sides of the casing.
Separate the metal chassis from the top cover, lifting the back of the chassis up and away from the top cover.
The plastic back panel is meant to stay attached to the metal chassis.
Step 4
- Flip the metal enclosure so that the fan cover is on top.
Flip the metal enclosure so that the fan cover is on top.
Step 5
Top Metal Shield
- Remove the two 15mm screws from the front panel using the Torx T8 screwdriver.
Remove the two 15mm screws from the front panel using the Torx T8 screwdriver.
Step 6
- Carefully slide the top metal case off the frame.
- This may require shifting the case side to side as you slide up.
Carefully slide the top metal case off the frame.
This may require shifting the case side to side as you slide up.
Step 7
Bottom Metal Shield
- Remove the eight 10mm screws from the bottom of the metal casing using the Torx T9 screwdriver.
- Remove the four 15mm screws from the bottom of the heatsink fastener using the Torx T8 screwdriver.
Remove the eight 10mm screws from the bottom of the metal casing using the Torx T9 screwdriver.
Remove the four 15mm screws from the bottom of the heatsink fastener using the Torx T8 screwdriver.
Step 8
- Remove the two plastic pieces from the motherboard.
Remove the two plastic pieces from the motherboard.
Step 9
- Lift the motherboard up from the metal chassis.
- The motherboard should easily separate from the metal chassis.
Lift the motherboard up from the metal chassis.
The motherboard should easily separate from the metal chassis.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 1 other contributor
Jules Hajjar
Member since: 10/10/2019
1,372 Reputation
8 Guides authored
Badges:
16
+13 more badges
Team
Cal Poly, Team S12-G6, Regan Fall 2019
Member of Cal Poly, Team S12-G6, Regan Fall 2019
CPSU-REGAN-F19S12G6
4 Members
24 Guides authored