Difficulty

Moderate

Steps

11

Time Required

                          15 - 30 minutes

Sections

3

  • Outer Shell
  • 3 steps
  • Heat Sink Assembly
  • 5 steps
  • Infrared Camera
  • 3 steps

Flags

2

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Missed a Step

Oops! This guide is currently missing some important steps.

  • BackXbox One Kinect

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Outer Shell
  • Remove the sticker on the underside of the device.
  • Remove the four 3.1x7.7 mm T9 screws underneath the sticker.
  • While you’re at it, remove the four 3.1x23.6 mm T9 screws beneath the sticker. Make note of the sizes and locations of the screws.

Remove the sticker on the underside of the device.

Remove the four 3.1x7.7 mm T9 screws underneath the sticker.

While you’re at it, remove the four 3.1x23.6 mm T9 screws beneath the sticker. Make note of the sizes and locations of the screws.

1024

Step 2

  • Remove the back panel.
  • Remove the black panels on either side of the Kinect, and remove the 3.1x7.7 mm T9 screws underneath them.

Remove the back panel.

Remove the black panels on either side of the Kinect, and remove the 3.1x7.7 mm T9 screws underneath them.

Step 3

  • Using your thumbs, press firmly against the outer case on either side of the stand. This will disengage the internal assembly.
  • Lift the internal assembly with the spudger.
  • Remove the assembly from the case. You now have access to the inner shell of the kinect, along with the heat sink, microphone, and LED sensor.

Using your thumbs, press firmly against the outer case on either side of the stand. This will disengage the internal assembly.

Lift the internal assembly with the spudger.

Remove the assembly from the case. You now have access to the inner shell of the kinect, along with the heat sink, microphone, and LED sensor.

Step 4

              Heat Sink Assembly
  • Remove the eight 2.9x7.6 mm T9 screws from the rear of the internal case.
  • Lift the internal metal case from the plastic shell enclosing the heat sink assembly.

Remove the eight 2.9x7.6 mm T9 screws from the rear of the internal case.

Lift the internal metal case from the plastic shell enclosing the heat sink assembly.

Step 5

  • Disconnect the ribbon cable between the sensor driver board and the motherboard.
  • Remove the 3.0x7.5 mm T9 screw holding the sensor driver board to the heat sink.
  • Remove the infrared sensor board for the Kinect.

Disconnect the ribbon cable between the sensor driver board and the motherboard.

Remove the 3.0x7.5 mm T9 screw holding the sensor driver board to the heat sink.

Remove the infrared sensor board for the Kinect.

Step 6

  • Detach the ribbon cable leading to the microphone with the tweezers.
  • Remove the four 3.1x7.7 mm T9 screws connecting the microphone to the heat sink assembly.
  • Remove the stand.

Detach the ribbon cable leading to the microphone with the tweezers.

Remove the four 3.1x7.7 mm T9 screws connecting the microphone to the heat sink assembly.

Remove the stand.

Step 7

  • Remove the eight 3.0x7.6 mm T9 screws from the motherboard.
  • Peel away the plastic film from the motherboard using the spudger.
  • Detach the ribbon cable leading to the color camera using the spudger.

Remove the eight 3.0x7.6 mm T9 screws from the motherboard.

Peel away the plastic film from the motherboard using the spudger.

Detach the ribbon cable leading to the color camera using the spudger.

Step 8

  • Lift the motherboard and the heat sink assembly from the plastic shell. The components attached to the heat sink are now accessible.

Lift the motherboard and the heat sink assembly from the plastic shell. The components attached to the heat sink are now accessible.

Step 9

              Infrared Camera
  • First step is to make sure that the inner compartment containg the camera is separated from the outer casing.

First step is to make sure that the inner compartment containg the camera is separated from the outer casing.

Step 10

  • Once the area where the camera is found is uncovered, use the T5 Torx Screwdriver to remove the four 1.9x10.2 mm screws.

Once the area where the camera is found is uncovered, use the T5 Torx Screwdriver to remove the four 1.9x10.2 mm screws.

Step 11

  • Using the spudger, detach the camera from the base.

Using the spudger, detach the camera from the base.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Laura Gonzalez

Member since: 09/22/2014

106 Reputation

                                      1 Guide authored                  



                       Badges:
                       2

Team

                       USF Tampa, Team 1-3, Hickman Fall 2014                        

                                                  Member of USF Tampa, Team 1-3, Hickman Fall 2014 



                    USFT-HICKMAN-F14S1G3                     


                                            4 Members                     


                                            7 Guides authored

mouyi chen - Nov 16, 2016

Reply

I have the new Infrared Camera ,1080p HD wide-angle camera,motherboard, IR projectors board.If you need please contact me.