Difficulty
Difficult
Steps
10
Time Required
2 hours
Sections
3
- Motherboard
- 7 steps
- Daughterboard
- 2 steps
- LED
- 1 step
Flags
1
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
BackXbox One Elite Wireless Controller Series 1 (Model 1698)
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Show me the Screws!
- You can remove the side panels with a pry tool.
- You don’t need to remove the rubber. The rubber on this controller was already bad
You can remove the side panels with a pry tool.
You don’t need to remove the rubber. The rubber on this controller was already bad
1024
Step 2
Removing the back panel screws
- Remove the 5 Torx Security Bit (TR9) screws
Remove the 5 Torx Security Bit (TR9) screws
Step 3
Popping that back panel off
- Pry the panel next to the 3.5mm port
- Be careful to not rip the ribbon shown in the next step
Pry the panel next to the 3.5mm port
Be careful to not rip the ribbon shown in the next step
Step 4
Warning Carefully remove the ribbon
- Be careful to not rip the ribbon cable
- You can pop the connector up to remove the ribbon easily
- Ribbon Cable
Be careful to not rip the ribbon cable
You can pop the connector up to remove the ribbon easily
Ribbon Cable
Step 5
Screws on controller motherboard
- Remove the 2 Torx (T6) screws
Remove the 2 Torx (T6) screws
Step 6
Desolder wires from motherboard
- Desolder the 4 wires on each side, these control the vibrations and the RT LT
Desolder the 4 wires on each side, these control the vibrations and the RT LT
Step 7
Remove the motherboard
- Pull up from the “top” side of the controller on the sister board.
Pull up from the “top” side of the controller on the sister board.
Step 8
Remove the Home Button Cover
- Be Careful to not lose the sync button
- Pry the middle section up from the home button side.
- This will also remove the LB and RB which is a single part
Be Careful to not lose the sync button
Pry the middle section up from the home button side.
This will also remove the LB and RB which is a single part
Step 9
Remove the controller daughterboard
- Unscrew the 6 Torx (T6) screws
Unscrew the 6 Torx (T6) screws
Step 10
Replace the LED
- Desolder the original LED from the motherboard of the controller. Do this for both sides of the LED until all of the old solder is removed.
- Solder on your new LED.
- Make sure it is installed the same direction as the old LED, or you can burn out the new LED.
Desolder the original LED from the motherboard of the controller. Do this for both sides of the LED until all of the old solder is removed.
Solder on your new LED.
Make sure it is installed the same direction as the old LED, or you can burn out the new LED.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
6 other people completed this guide.
Author
with 2 other contributors
EasyAsABC123
Member since: 01/22/2010
2,273 Reputation
5 Guides authored
Badges:
25
+22 more badges
Dustin Dykstra - Oct 8, 2017
Reply
So question I’m having troubles with my elite controller every time I go to plug it in and the charging port in the back of the controller it starts to smoke what’s my problem
EasyAsABC123 - Oct 8, 2017
It sounds like it could be a lot of things…
smoke is obvious a dead stop (stop plugging it in until you repair it).
I would first check the charge port and make sure it is firmly attached if it isn’t you can easily replace the usb port. Next it could be the mainboard charging circuit. if it is this…replace the controller is likely the ideal solution.
Clayton Armagost - Jun 16, 2018
Reply
I was looking to do this mod for fun. Do you have or know where I can get the led part number? A schematic or bom would be nice. Thanks
EasyAsABC123 - Jun 19, 2018
0805 SMD LED Diode Lights
i bought these https://www.amazon.com/gp/product/B01CUG…
Clayton Armagost - Jun 20, 2018
Thank you. I ordered them so we will see what happens.