Difficulty

Moderate

Steps

10

Time Required

                          15 - 30 minutes

Sections

5

  • Battery
  • 1 step
  • Rear Case
  • 5 steps
  • Vibration Motors
  • 2 steps
  • Logic Board
  • 1 step
  • Bumper Panel
  • 1 step

Flags

0

  • BackXbox 360 Wireless Controller

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Depress the battery release button on the top of the controller.
  • Remove the battery holder from the controller.
  • The standard option for Xbox 360 Wireless Controllers Battery Packs is AA batteries. A rechargeable battery is also available, but both battery options are removed from the controller in the same way.

Depress the battery release button on the top of the controller.

Remove the battery holder from the controller.

The standard option for Xbox 360 Wireless Controllers Battery Packs is AA batteries. A rechargeable battery is also available, but both battery options are removed from the controller in the same way.

1024

Step 2

              Rear Case
  • Use a pair of tweezers to peel the barcode sticker from the battery compartment.

Use a pair of tweezers to peel the barcode sticker from the battery compartment.

Step 3

  • Remove the seven 9.3 mm T8 Security Torx screws securing the rear case to the front case.

Remove the seven 9.3 mm T8 Security Torx screws securing the rear case to the front case.

Step 4

  • Insert a Spudger between the front and rear cases along the left edge of the controller.
  • Rotate the spudger toward the front of the controller, prying the two cases apart.

Insert a Spudger between the front and rear cases along the left edge of the controller.

Rotate the spudger toward the front of the controller, prying the two cases apart.

Step 5

  • Insert a spudger between the front and rear cases, near the headphone jack.
  • Rotate the spudger toward the front of the controller to pry the two cases apart.

Insert a spudger between the front and rear cases, near the headphone jack.

Rotate the spudger toward the front of the controller to pry the two cases apart.

Step 6

  • Grasp the controller by the battery compartment and the headphone jack.
  • Lift the battery compartment away from the headphone jack, separating the rear case from the front case and logic board.
  • The battery contact springs are held in place by slots in the battery housing in the rear case. Be sure to realign them properly during reassembly.

Grasp the controller by the battery compartment and the headphone jack.

Lift the battery compartment away from the headphone jack, separating the rear case from the front case and logic board.

The battery contact springs are held in place by slots in the battery housing in the rear case. Be sure to realign them properly during reassembly.

Step 7

              Vibration Motors
  • Use the flat end of a spudger to remove the vibration motor cable, moving it upward from its socket on the logic board.
  • Lift the vibration motor out of the front case.

Use the flat end of a spudger to remove the vibration motor cable, moving it upward from its socket on the logic board.

Lift the vibration motor out of the front case.

Step 8

  • Remove the vibration motor from the other side of the controller using the same method previously described.
  • The left motor has significantly more counterweight than the right motor.

Remove the vibration motor from the other side of the controller using the same method previously described.

The left motor has significantly more counterweight than the right motor.

Step 9

              Logic Board
  • Lifting from the headphone jack and power plug, remove the logic board from the front case.

Lifting from the headphone jack and power plug, remove the logic board from the front case.

Step 10

              Bumper Panel
  • Orient the controller so that the front of the controller is facing toward you.
  • Lift the bumper panel off the front case.

Orient the controller so that the front of the controller is facing toward you.

Lift the bumper panel off the front case.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      26 other people completed this guide.

Author

                                      with 6 other contributors 


                    Brett Hartt

Member since: 04/12/2010

125,280 Reputation

                                      143 Guides authored                  



                       Badges:
                       52







                                                        +49 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,767 Guides authored