Difficulty
Moderate
Steps
11
Time Required
15 minutes
Sections
5
- Battery
- 1 step
- Rear Case
- 5 steps
- Vibration Motors
- 2 steps
- Logic Board
- 1 step
- Analog Stick Covers
- 2 steps
Flags
0
BackXbox 360 Wireless Controller
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Depress the battery release button on the top of the controller.
- Remove the battery holder from the controller.
- The standard option for Xbox 360 Wireless Controllers Battery Packs is AA batteries. A rechargeable battery is also available, but both battery options are removed from the controller in the same way.
Depress the battery release button on the top of the controller.
Remove the battery holder from the controller.
The standard option for Xbox 360 Wireless Controllers Battery Packs is AA batteries. A rechargeable battery is also available, but both battery options are removed from the controller in the same way.
1024
Step 2
Rear Case
- Use a pair of tweezers to peel the barcode sticker from the battery compartment.
Use a pair of tweezers to peel the barcode sticker from the battery compartment.
Step 3
- Remove the seven 9.3 mm T8 Security Torx screws securing the rear case to the front case.
Remove the seven 9.3 mm T8 Security Torx screws securing the rear case to the front case.
Step 4
- Insert a Spudger between the front and rear cases along the left edge of the controller.
- Rotate the spudger toward the front of the controller, prying the two cases apart.
Insert a Spudger between the front and rear cases along the left edge of the controller.
Rotate the spudger toward the front of the controller, prying the two cases apart.
Step 5
- Insert a spudger between the front and rear cases, near the headphone jack.
- Rotate the spudger toward the front of the controller to pry the two cases apart.
Insert a spudger between the front and rear cases, near the headphone jack.
Rotate the spudger toward the front of the controller to pry the two cases apart.
Step 6
- Grasp the controller by the battery compartment and the headphone jack.
- Lift the battery compartment away from the headphone jack, separating the rear case from the front case and logic board.
- The battery contact springs are held in place by slots in the battery housing in the rear case. Be sure to realign them properly during reassembly.
Grasp the controller by the battery compartment and the headphone jack.
Lift the battery compartment away from the headphone jack, separating the rear case from the front case and logic board.
The battery contact springs are held in place by slots in the battery housing in the rear case. Be sure to realign them properly during reassembly.
Step 7
Vibration Motors
- Use the flat end of a spudger to remove the vibration motor cable, moving it upward from its socket on the logic board.
- Lift the vibration motor out of the front case.
Use the flat end of a spudger to remove the vibration motor cable, moving it upward from its socket on the logic board.
Lift the vibration motor out of the front case.
Step 8
- Remove the vibration motor from the other side of the controller using the same method previously described.
- The left motor has significantly more counterweight than the right motor.
Remove the vibration motor from the other side of the controller using the same method previously described.
The left motor has significantly more counterweight than the right motor.
Step 9
Logic Board
- Lifting from the headphone jack and power plug, remove the logic board from the front case.
Lifting from the headphone jack and power plug, remove the logic board from the front case.
Step 10
Analog Stick Covers
- Grasp the right analog stick and pull the cover off its mount peg.
Grasp the right analog stick and pull the cover off its mount peg.
Step 11
- Remove the left analog stick cover using the same procedure previously described.
Remove the left analog stick cover using the same procedure previously described.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
88 other people completed this guide.
Author
with 3 other contributors
Brett Hartt
Member since: 04/12/2010
125,280 Reputation
143 Guides authored
Badges:
52
+49 more badges
Team
iFixit
Member of iFixit
Community
141 Members
15,767 Guides authored
zachharrizusnavy - Oct 18, 2019
Reply
unnecessary steps.
3 steps:
remove all 7 screws.
flip upside down remove top plate
pull stick caps off
reinstall in reverse.
you may have to slide the vibration motors into the slots on the top half when putting back together.