Xbox 360 S Wi Fi Board Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          5 minutes

Sections

Top Panel
11 steps
Wi-Fi Board
1 step

Flags

BackXbox 360 S
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Top Panel

In the following steps, you will remove the top vent, secured to the top panel by the thirteen clips shown.
Take care when removing the fan vent not to break any of the plastic clips.

In the following steps, you will remove the top vent, secured to the top panel by the thirteen clips shown.

Take care when removing the fan vent not to break any of the plastic clips.

1024

Step 2

Orient the console so that the words “XBOX 360” on the sides are right-side up, and the faceplate is facing to the left.
Insert a metal spudger between the top vent and the top bezel near the rear of the Xbox.
Rotate the spudger away from the console, prying the edge of the fan vent up until the two plastic clips come free.
Be sure to rotate the spudger far enough so that the plastic clips clear the silver rim of the top bezel.

Orient the console so that the words “XBOX 360” on the sides are right-side up, and the faceplate is facing to the left.

Insert a metal spudger between the top vent and the top bezel near the rear of the Xbox.

Rotate the spudger away from the console, prying the edge of the fan vent up until the two plastic clips come free.

Be sure to rotate the spudger far enough so that the plastic clips clear the silver rim of the top bezel.

Step 3

Insert a metal spudger between the fan vent and top bezel along the left side of the console.
In the same manner described above, begin prying the left side of the top vent away from the top bezel.
Continue prying along the left side of the device, freeing all the clips on that side.

Insert a metal spudger between the fan vent and top bezel along the left side of the console.

In the same manner described above, begin prying the left side of the top vent away from the top bezel.

Continue prying along the left side of the device, freeing all the clips on that side.

Step 4

Lift the fan vent up from the freed left side to disengage the clips along the right side.
Remove the entire fan vent.

Lift the fan vent up from the freed left side to disengage the clips along the right side.

Remove the entire fan vent.

Step 5

In the following steps, you will be releasing the six clips highlighted in red.
Each clip can be undone by inserting a metal spudger underneath the bottom edge of the clip. Once underneath the bottom edge, simply prying away from the console will free the clip.

In the following steps, you will be releasing the six clips highlighted in red.

Each clip can be undone by inserting a metal spudger underneath the bottom edge of the clip. Once underneath the bottom edge, simply prying away from the console will free the clip.

Step 6

Orient the console so that the left case is facing toward you and the faceplate is facing toward the right.
Insert a metal spudger through the front-most slit on the left edge of the top bezel and between the bottom edge of the clip and the left case, as described above.
Simultaneously rotate the spudger away from the console and pull up on the top bezel to free the clip.
You will hear a “pop” signifying that the clip cleared its catch.

Orient the console so that the left case is facing toward you and the faceplate is facing toward the right.

Insert a metal spudger through the front-most slit on the left edge of the top bezel and between the bottom edge of the clip and the left case, as described above.

Simultaneously rotate the spudger away from the console and pull up on the top bezel to free the clip.

You will hear a “pop” signifying that the clip cleared its catch.

Step 7

Using the same method described above, free the two remaining clips along the left edge of the top bezel.

Using the same method described above, free the two remaining clips along the left edge of the top bezel.

Step 8

Grab the entire top panel with your hands, lift up the entire left edge high enough to rest the separated clips on top of the left case.
You may have to go back with a spudger and undo any clips that have re-attached.
The top panel will not come free of the console yet.

Grab the entire top panel with your hands, lift up the entire left edge high enough to rest the separated clips on top of the left case.

You may have to go back with a spudger and undo any clips that have re-attached.

The top panel will not come free of the console yet.

Step 9

Rotate the console so that the rear of the Xbox 360 S is facing to the right, and the right case is facing you.
Insert a metal spudger through the rear-most slit on the right edge of the top bezel and between the bottom edge of the clip and the right case.
While lifting up on the top bezel with your fingers, rotate the spudger away from the console to free the clip.

Rotate the console so that the rear of the Xbox 360 S is facing to the right, and the right case is facing you.

Insert a metal spudger through the rear-most slit on the right edge of the top bezel and between the bottom edge of the clip and the right case.

While lifting up on the top bezel with your fingers, rotate the spudger away from the console to free the clip.

Step 10

In the same manner as described in the previous steps, release the middle and front clips along the right edge of the top panel.

In the same manner as described in the previous steps, release the middle and front clips along the right edge of the top panel.

Step 11

Lift the top panel off the device.
You may have to go back with a spudger and undo any clips that have re-attached to the console.

Lift the top panel off the device.

You may have to go back with a spudger and undo any clips that have re-attached to the console.

Step 12

              Wi-Fi Board

Remove the single T10 Torx screw holding in the wireless card.
Pull the Wi-Fi board out of the console.

Remove the single T10 Torx screw holding in the wireless card.

Pull the Wi-Fi board out of the console.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      35 other people completed this guide.

Author

                                      with 5 other contributors

                    Brett Hartt

Member since: 04/12/2010

125,280 Reputation

                                      143 Guides authored                  



                       Badges:
                       52







                                                        +49 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,767 Guides authored

mattinnihon - Sep 10, 2013

My Slim came without the wifi board, and subsequently without the holding screw.

Anyone know the thread, size, or depth of a replacement screw I could use to hold the replacement in? It seems like it won’t go anywhere with the pseudo-USB connector in place, but I’d like to be positive.

Any help would be appreciated!

andreshgarcia20 - Mar 15, 2015

Tuve ese mismo problema. Fui a una tienda y el técnico tuvo que quitarle la tarjeta de WiFi a otro xbox porque no hay repuesto

sarncadrill - Mar 5, 2016

Worth noting.. Before you purchase a new wifi card, try taking it out and reseating it. Just had to do that with mine when the wifi suddenly stopped working. Once I pulled the card and put it back in, it worked beautifully.

Also, for clarification, you are opening the side OPPOSITE the side with the hard drive.

Introduction#

What you need#

Team#

Introduction

What you need

Team