Xbox 360 Lower Case Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

Suggest a time??

Sections

Hard Drive
1 step
Bottom Vent
6 steps
Faceplate
3 steps
Top Vent
6 steps
Lower Case
9 steps

Flags

BackXbox 360
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Hard Drive

Grasp the hard drive assembly and press the release button while lifting its front edge.
Remove the hard drive assembly from the top vent.

Grasp the hard drive assembly and press the release button while lifting its front edge.

Remove the hard drive assembly from the top vent.

1024

Step 2

              Bottom Vent

Stand the console vertically with the bottom edge facing up.
Throughout the following opening procedure, the finger of an Xbox 360 opening tool can be used in place of a spudger.
Insert the flat end of a spudger or the edge of an Xbox 360 opening tool into the small gap at the front edge of the bottom vent.
Pry the front edge of the bottom vent away from the faceplate.

Stand the console vertically with the bottom edge facing up.

Throughout the following opening procedure, the finger of an Xbox 360 opening tool can be used in place of a spudger.

Insert the flat end of a spudger or the edge of an Xbox 360 opening tool into the small gap at the front edge of the bottom vent.

Pry the front edge of the bottom vent away from the faceplate.

Step 3

In the next few steps, you will use the tip of a spudger or the finger of an Xbox 360 opening tool to release the clips along the left and right sides of the bottom vent. Their locations are highlighted in red.
You will insert the tool into the holes molded into the white plastic side case pieces.

In the next few steps, you will use the tip of a spudger or the finger of an Xbox 360 opening tool to release the clips along the left and right sides of the bottom vent. Their locations are highlighted in red.

You will insert the tool into the holes molded into the white plastic side case pieces.

Step 4

To release the clips, work from the front edge of the bottom vent.
While slightly lifting the front edge of the bottom vent, use the tip of a spudger to push the clips closest to the front of the bottom vent towards the inside of the console.

To release the clips, work from the front edge of the bottom vent.

While slightly lifting the front edge of the bottom vent, use the tip of a spudger to push the clips closest to the front of the bottom vent towards the inside of the console.

Step 5

Repeat the same process to release the two center clips on the bottom vent.

Repeat the same process to release the two center clips on the bottom vent.

Step 6

Use the tip of your spudger to release the clips on the bottom vent nearest the back of the Xbox.

Use the tip of your spudger to release the clips on the bottom vent nearest the back of the Xbox.

Step 7

Remove the bottom vent from the 360.

Remove the bottom vent from the 360.

Step 8

              Faceplate

Insert the flat edge of a spudger between the faceplate and the outer casing near the power button.
Run your spudger along the edge of the faceplate to release the clips securing it to the front of the console.
You may also accomplish this task by using the edge of the Xbox 360 opening tool, but it may scratch the plastic case.
Alternatively, you can use your hands to carefully pull the faceplate away from the Xbox.

Insert the flat edge of a spudger between the faceplate and the outer casing near the power button.

Run your spudger along the edge of the faceplate to release the clips securing it to the front of the console.

You may also accomplish this task by using the edge of the Xbox 360 opening tool, but it may scratch the plastic case.

Alternatively, you can use your hands to carefully pull the faceplate away from the Xbox.

Step 9

Repeat the same motions as previously mentioned to release the left side of the faceplate.

Repeat the same motions as previously mentioned to release the left side of the faceplate.

Step 10

Remove the faceplate from the front face of the console.

Remove the faceplate from the front face of the console.

Step 11

              Top Vent

Stand the console vertically with the top edge facing up.
The top vent is secured to the console via clips. The first two clips are located underneath the top vent closest to the faceplate, as shown in the pictures.

Stand the console vertically with the top edge facing up.

The top vent is secured to the console via clips. The first two clips are located underneath the top vent closest to the faceplate, as shown in the pictures.

Step 12

Insert the flat end of a spudger into the small gaps previously mentioned to release the clips.
You may also use the long finger of an Xbox 360 opening tool to accomplish this task.

Insert the flat end of a spudger into the small gaps previously mentioned to release the clips.

You may also use the long finger of an Xbox 360 opening tool to accomplish this task.

Step 13

In the next few steps, you will use the tip of a spudger or the finger of an Xbox 360 opening tool to release the clips along the left and right sides of the top vent. Their locations are highlighted in red.

In the next few steps, you will use the tip of a spudger or the finger of an Xbox 360 opening tool to release the clips along the left and right sides of the top vent. Their locations are highlighted in red.

Step 14

To release the clips, work from the middle of the top vent.
While slightly lifting the front edge of the top vent, use the tip of a spudger to push the clips closest to the center of the top vent towards the inside of the console.

To release the clips, work from the middle of the top vent.

While slightly lifting the front edge of the top vent, use the tip of a spudger to push the clips closest to the center of the top vent towards the inside of the console.

Step 15

Use the tip of your spudger to release the clip on the top vent nearest the back of the Xbox’s upper case.

Use the tip of your spudger to release the clip on the top vent nearest the back of the Xbox’s upper case.

Step 16

The last clip is hidden underneath the rubber foot nearest the back of the console.
Use the tip of your spudger to release the clip on the top vent nearest the back of the Xbox.
Remove the top vent from the 360.

The last clip is hidden underneath the rubber foot nearest the back of the console.

Use the tip of your spudger to release the clip on the top vent nearest the back of the Xbox.

Remove the top vent from the 360.

Step 17

              Lower Case

Stand the console vertically with the top edge facing down.
Carefully peel the warranty sticker off the console.

Stand the console vertically with the top edge facing down.

Carefully peel the warranty sticker off the console.

Step 18

The upper and lower cases are attached via several latches, located in the front and back of the console. These latches must be disengaged to separate the upper case from the console.
Use the flat end of a spudger to release the following latches:
Above the front-facing USB ports.
Beneath the front-facing USB ports.
Above the Memory Unit slots.

The upper and lower cases are attached via several latches, located in the front and back of the console. These latches must be disengaged to separate the upper case from the console.

Use the flat end of a spudger to release the following latches:

Above the front-facing USB ports.

Beneath the front-facing USB ports.

Above the Memory Unit slots.

Step 19

Insert the flat end of a spudger and pry upwards to release the last remaining latch located above the eject button.

Insert the flat end of a spudger and pry upwards to release the last remaining latch located above the eject button.

Step 20

Slightly lift the front portion of the lower case to ensure that the latches in the front have been completely released.

Slightly lift the front portion of the lower case to ensure that the latches in the front have been completely released.

Step 21

The upper and lower cases are held together by seven release latches located on the back of the console. Their locations are highlighted in red.

The upper and lower cases are held together by seven release latches located on the back of the console. Their locations are highlighted in red.

Step 22

Press the Xbox 360 opening tool down into the clips securing the lower case to the upper case near the I/O ports.
While pressing down on the tool, push the lower and upper cases apart to separate the retaining clips.

Press the Xbox 360 opening tool down into the clips securing the lower case to the upper case near the I/O ports.

While pressing down on the tool, push the lower and upper cases apart to separate the retaining clips.

Step 23

While pushing the upper and lower cases apart, use the tip of a spudger or the finger of an Xbox 360 opening tool to push the long clip highlighted in red toward the center of the 360.
The clip should release, leaving the clips near the power connector as the only thing holding the upper and lower cases together.

While pushing the upper and lower cases apart, use the tip of a spudger or the finger of an Xbox 360 opening tool to push the long clip highlighted in red toward the center of the 360.

The clip should release, leaving the clips near the power connector as the only thing holding the upper and lower cases together.

Step 24

Press the Xbox 360 opening tool down into the two remaining clips near the power connector.
Push the upper and lower cases apart to fully release the retaining clips.

Press the Xbox 360 opening tool down into the two remaining clips near the power connector.

Push the upper and lower cases apart to fully release the retaining clips.

Step 25

Orient the console so that the front portion is facing downwards.
Grasp the back portion of the lower case and lift it upwards to separate it from the console.
Be careful not to excessively bend the lower case near the power plug, as it can crack easily.

Orient the console so that the front portion is facing downwards.

Grasp the back portion of the lower case and lift it upwards to separate it from the console.

Be careful not to excessively bend the lower case near the power plug, as it can crack easily.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      39 other people completed this guide.

Author

                                      with 9 other contributors

                    Walter Galan

682,038 Reputation

                                      1,203 Guides authored                  



                       Badges:
                       54







                                                        +51 more badges

Nathan - Oct 22, 2017

Can you also use a spudger to release the back clips or will this damage the case?

Introduction#

What you need#

Introduction

What you need