Featured
Featured Guide
Difficulty
Moderate
Steps
16
Time Required
5 minutes
Sections
6
- Top Panel
- 3 steps
- Wi-Fi Card
- 2 steps
- Bottom Panel
- 3 steps
- Top Body
- 1 step
- Bottom Body
- 4 steps
- CD Drive
- 3 steps
Flags
2
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
Featured Guide
This guide has been found to be exceptionally cool by the iFixit staff.
BackXbox 360 E
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Top Panel
- Push the Spudger into the crevice between the grated top panel of the Xbox and the bottom body with the rubber feet.
- Pull back on the spudger like a lever, keeping it pressed firmly into the crevice.
Push the Spudger into the crevice between the grated top panel of the Xbox and the bottom body with the rubber feet.
Pull back on the spudger like a lever, keeping it pressed firmly into the crevice.
1024
Step 2
- Slide the spudger along the separation you have created between the grated panel and the bottom body of the Xbox.
- Periodically pull back on the spudger like a lever, keeping it pressed firmly into the crevice.
Slide the spudger along the separation you have created between the grated panel and the bottom body of the Xbox.
Periodically pull back on the spudger like a lever, keeping it pressed firmly into the crevice.
Step 3
- Continue sliding the spudger along the perimeter of the left grated face of the Xbox.
- Pull the top panel off.
Continue sliding the spudger along the perimeter of the left grated face of the Xbox.
Pull the top panel off.
Step 4
Wi-Fi Card
- Remove the 11 mm screw left of the green wifi-card using the T9 Torx screw bit.
Remove the 11 mm screw left of the green wifi-card using the T9 Torx screw bit.
Step 5
- Firmly grip the green Wi-Fi card and pull it out of the Xbox.
Firmly grip the green Wi-Fi card and pull it out of the Xbox.
Step 6
Bottom Panel
- Push the spudger into the crevice between the right grated face and the top body of the Xbox. It’s easier to begin away from the vent.
- Pull up on the spudger like a lever, keeping it pressed firmly into the crevice.
Push the spudger into the crevice between the right grated face and the top body of the Xbox. It’s easier to begin away from the vent.
Pull up on the spudger like a lever, keeping it pressed firmly into the crevice.
Step 7
- Slide the spudger along the crevice to separate the grated face and the top body.
Slide the spudger along the crevice to separate the grated face and the top body.
Step 8
- Wiggle the spudger in the crevice as you slide the spudger to loosen the bottom plate.
- Slide the spudger along the crevice, going completely about the perimeter of the bottom panel.
- Pull the bottom panel off.
Wiggle the spudger in the crevice as you slide the spudger to loosen the bottom plate.
Slide the spudger along the crevice, going completely about the perimeter of the bottom panel.
Pull the bottom panel off.
Step 9
Top Body
- Remove the five long black 55 mm screws labeled C2-5 and C7 with a T9 Torx screwdriver.
- Carefully flip the device and pull off the body by lifting from the metal section that is attached to the plastic exterior.
Remove the five long black 55 mm screws labeled C2-5 and C7 with a T9 Torx screwdriver.
Carefully flip the device and pull off the body by lifting from the metal section that is attached to the plastic exterior.
Step 10
Bottom Body
- Orient the Xbox so the bottom body is facing upwards. Make sure you see the rubber feet to know you have the correct side of the device.
- Lift the bottom body slightly away from the core at a 45 degree angle.
Orient the Xbox so the bottom body is facing upwards. Make sure you see the rubber feet to know you have the correct side of the device.
Lift the bottom body slightly away from the core at a 45 degree angle.
Step 11
- Rotate the Xbox so you are now looking at the back of the device.
- This step of disassembly requires the removal of the warranty sticker. This will void your warranty. Check the main page for a link to warranty information from Microsoft.
- Remove the sticker from the back of the Xbox.
- The sticker is not needed for reassembly.
Rotate the Xbox so you are now looking at the back of the device.
This step of disassembly requires the removal of the warranty sticker. This will void your warranty. Check the main page for a link to warranty information from Microsoft.
Remove the sticker from the back of the Xbox.
The sticker is not needed for reassembly.
Step 12
- Turn the Xbox to the left to locate the clip holding the body together.
- With a spudger, press up on the clip like a latch. Move to the far end to undo the other clip the same way.
Turn the Xbox to the left to locate the clip holding the body together.
With a spudger, press up on the clip like a latch. Move to the far end to undo the other clip the same way.
Step 13
- Push the spudger into the crevice. Slide the spudger along the vertical crevice to detach the last clip. The bottom body should slide off after this.
Push the spudger into the crevice. Slide the spudger along the vertical crevice to detach the last clip. The bottom body should slide off after this.
Step 14
CD Drive
- Use your fingers to unplug the blue ribbon cable from the CD drive.
Use your fingers to unplug the blue ribbon cable from the CD drive.
Step 15
- Use tweezers to unplug the blue and pink wires.
Use tweezers to unplug the blue and pink wires.
Step 16
- Lift the front end of the CD drive and take it out.
Lift the front end of the CD drive and take it out.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
21 other people completed this guide.
Author
with 3 other contributors
George
Member since: 02/02/2014
521 Reputation
1 Guide authored
Badges:
11
+8 more badges
Team
Cal Poly, Team 2-11, Amido Winter 2014
Member of Cal Poly, Team 2-11, Amido Winter 2014
CPSU-AMIDO-W14S2G11
4 Members
31 Guides authored
sandjo - Mar 25, 2016
Reply
i wish the bottom cover magically came off like in step 9
Andrew Boyd - May 19, 2016
Reply
screws are actually C1- C5 one is incorrectly labelled - C7 = C1 also in step 8.5 there are 3 clips holding back edge of bottom cover to top one. one on each end and one just to right of I/O area. can get 2 of them with a spudger (ends) and the middle one with a isesamo.
Freddie Parsons - Jan 31, 2017
Reply
Several steps missing between 8 and 9
william capewell - Aug 1, 2019
Like remove wifi adaptor.
Joe G. - Aug 28, 2018
Reply
There is some consistency errors in this guide. Step 9 seems to blast ahead beyond where we should be at this point of the guide.