Difficulty
Difficult
Steps
14
Time Required
25 - 35 minutes
Sections
3
- Battery
- 2 steps
- Underbody
- 9 steps
- Rear Motor
- 3 steps
Flags
0
BackX-Street Lamborghini Murcielago LP670-4 SV
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Unscrew the two 2.5mm Phillips #00 screws from the middle of the car.
- Unclip the two clips to remove the battery cover.
Unscrew the two 2.5mm Phillips #00 screws from the middle of the car.
Unclip the two clips to remove the battery cover.
1024
Step 2
- Unplug the battery by pushing on the clip.
Unplug the battery by pushing on the clip.
Step 3
Underbody
- Unscrew the two 2.5mm Phillips #00 screws from each side
Unscrew the two 2.5mm Phillips #00 screws from each side
Step 4
- Remove the side skirt covers on each side of the car.
Remove the side skirt covers on each side of the car.
Step 5
- Lift up and remove the two side skirts.
Lift up and remove the two side skirts.
Step 6
- Unscrew the two 2.5mm Phillips #00 screws from the front skirt of the car.
Unscrew the two 2.5mm Phillips #00 screws from the front skirt of the car.
Step 7
- Lift the front part of the underbody and pull it out from the main underbody.
Lift the front part of the underbody and pull it out from the main underbody.
Step 8
- Unscrew the remaining seven 9mm Phillips #00 screws from the underbody of the car.
- The second image shows a closer view of the rear three screws
Unscrew the remaining seven 9mm Phillips #00 screws from the underbody of the car.
The second image shows a closer view of the rear three screws
Step 9
- Lift the main underbody from the shell of the car.
- Lift up the body to expose the wiring and hardware underneath.
Lift the main underbody from the shell of the car.
Lift up the body to expose the wiring and hardware underneath.
Step 10
- Remove the reflective sticker from the top of the body.
Remove the reflective sticker from the top of the body.
Step 11
- Unplug the wire connector.
Unplug the wire connector.
Step 12
Rear Motor
- Unscrew the two 2.5mm Phillips #00 screws on the white covering of the rear motor casing.
- There is a plastic casing over the rear motor. Simply remove this plastic covering and proceed.
Unscrew the two 2.5mm Phillips #00 screws on the white covering of the rear motor casing.
There is a plastic casing over the rear motor. Simply remove this plastic covering and proceed.
Step 13
- Remove all ten 1.6mm Phillips #000 screws from the rear motor casing
- The first image shows five screws on the side with the circuitry
- The second image shows five screws on the opposite side of the casing.
Remove all ten 1.6mm Phillips #000 screws from the rear motor casing
The first image shows five screws on the side with the circuitry
The second image shows five screws on the opposite side of the casing.
Step 14
- Use a soldering gun to remove the attached wires
Use a soldering gun to remove the attached wires
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 4 other contributors
Trent Peterson
Member since: 04/01/2015
448 Reputation
3 Guides authored
Badges:
11
+8 more badges
Team
Cal Poly, Team 24-3, Lancaster Spring 2015
Member of Cal Poly, Team 24-3, Lancaster Spring 2015
CPSU-LANCASTER-S15S24G3
3 Members
9 Guides authored
mattsson97 - Jan 13, 2017
Reply
what size is the motor
