Difficulty
Moderate
Steps
11
Time Required
30 - 45 minutes
Sections
4
- Battery
- 2 steps
- Wheel
- 3 steps
- WowWee MiP Robot Body Disassembly
- 3 steps
- Speaker
- 3 steps
Flags
0
BackWowWee MiP Robot
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Remove the three 12.0 mm Phillips # 2 screws from the battery cover.
Remove the three 12.0 mm Phillips # 2 screws from the battery cover.
1024
Step 2
- Carefully pull the battery pack from the robot.
- Remove the batteries from the battery pack.
Carefully pull the battery pack from the robot.
Remove the batteries from the battery pack.
Step 3
Wheel
- Use a metal spudger to carefully pry off the hubcap without marring the plastic wheel or hubcap.
- This plastic material is not replaceable. Any damage will be noticeable.
Use a metal spudger to carefully pry off the hubcap without marring the plastic wheel or hubcap.
This plastic material is not replaceable. Any damage will be noticeable.
Step 4
- Remove the 12.0 mm Phillips #2 screw.
- Hold the wheel in place, or it will rotate as you attempt to remove the screw.
Remove the 12.0 mm Phillips #2 screw.
Hold the wheel in place, or it will rotate as you attempt to remove the screw.
Step 5
- Pull the wheel off of the square axle.
- Do not use excessive force while removing the wheel. Pulling too hard on the wheel can damage the axle.
Pull the wheel off of the square axle.
Do not use excessive force while removing the wheel. Pulling too hard on the wheel can damage the axle.
Step 6
WowWee MiP Robot Body Disassembly
- Remove the eight 9.3 mm Phillips #1 screws from the back of the robot.
Remove the eight 9.3 mm Phillips #1 screws from the back of the robot.
Step 7
- Remove the arms from the body.
- Carefully open the body compartment.
- Open the compartment slowly. There are wires connecting the two body pieces together. If pulled too hard, the wires and/or the motherboard could be damaged.
Remove the arms from the body.
Carefully open the body compartment.
Open the compartment slowly. There are wires connecting the two body pieces together. If pulled too hard, the wires and/or the motherboard could be damaged.
Step 8
- Using precision tweezers, disconnect the following three bundles of wires:
- Connecting the battery pack to the motherboard.
- Connecting the power switch to the motherboard.
- Connecting the speaker to the motherboard.
Using precision tweezers, disconnect the following three bundles of wires:
Connecting the battery pack to the motherboard.
Connecting the power switch to the motherboard.
Connecting the speaker to the motherboard.
Step 9
Speaker
- Remove the two 7.5 mm Phillips #1 screws holding the speaker bracket in place.
Remove the two 7.5 mm Phillips #1 screws holding the speaker bracket in place.
Step 10
- Remove the plastic bracket covering the speaker.
Remove the plastic bracket covering the speaker.
Step 11
- Gently remove the speaker from the MiP.
- During reassembly, be sure to place the speaker in the same position.
Gently remove the speaker from the MiP.
During reassembly, be sure to place the speaker in the same position.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Daniel Burkholder
Member since: 02/16/2016
623 Reputation
4 Guides authored
Badges:
10
+7 more badges
Team
USF Tampa, Team 3-4, Wollert Spring 2016
Member of USF Tampa, Team 3-4, Wollert Spring 2016
USFT-WOLLERT-S16S3G4
4 Members
5 Guides authored