Difficulty
Moderate
Steps
5
Time Required
10 - 20 minutes
Sections
1
- Picket
- 5 steps
Flags
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
BackHome Construction
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
Before completing the rest of this guide, complete Step 1. This is needed to get the measurements of the picket you are replacing so you can purchase a replacement.
This materials listed in this guide reflect the materials needed to replace a single picket. For every additional picket being replaced, add 6 x 2 1/2” Wood Nails.
What you need
Step 1
Picket
- IMPORTANT: This step will need to be completed before continuing. You will need to use these measurements to purchase a replacement picket needed later in the guide.
- Use the tape measure to measure the height, width, and depth of the picket.
- Use these measurements to purchase a replacement picket. Home Depot and Lowe’s are good places to purchase a picket. If you are unfamiliar with what you are doing, ask any worker there for some help and they will help you get your replacement.
IMPORTANT: This step will need to be completed before continuing. You will need to use these measurements to purchase a replacement picket needed later in the guide.
Use the tape measure to measure the height, width, and depth of the picket.
Use these measurements to purchase a replacement picket. Home Depot and Lowe’s are good places to purchase a picket. If you are unfamiliar with what you are doing, ask any worker there for some help and they will help you get your replacement.
1024
Step 2
- Place the tip of the pry bar under the picket, in line with the nails.
- Use a hammer to push the pry bar under the picket.
- Use soft taps with the hammer when hitting the pry bar. Using too much force may reduce accuracy and lead to injury.
- Pull the pry bar away from the fence to remove the picket.
Place the tip of the pry bar under the picket, in line with the nails.
Use a hammer to push the pry bar under the picket.
Use soft taps with the hammer when hitting the pry bar. Using too much force may reduce accuracy and lead to injury.
Pull the pry bar away from the fence to remove the picket.
Step 3
- Only complete this step if there are still nails in the wood after you have removed the picket. If all nails are removed, continue to Step 4.
- Slide the claw of the hammer underneath the nail.
- The claw is the forked area of the hammer. This is commonly used to aid in the removal of nails.
- While holding the handle, pull on the hammer to remove the nail.
Only complete this step if there are still nails in the wood after you have removed the picket. If all nails are removed, continue to Step 4.
Slide the claw of the hammer underneath the nail.
The claw is the forked area of the hammer. This is commonly used to aid in the removal of nails.
While holding the handle, pull on the hammer to remove the nail.
Step 4
- Before installing the new picket, clear the area of any debris.
- Obstructions may cause the picket to be crooked when installing, or make a gap too large for the nails to work properly.
- Use the tape measure to measure the gaps between the left and right side of the picket.
- Doing this allows the replacement picket to be centered directly between the other pickets.
Before installing the new picket, clear the area of any debris.
Obstructions may cause the picket to be crooked when installing, or make a gap too large for the nails to work properly.
Use the tape measure to measure the gaps between the left and right side of the picket.
Doing this allows the replacement picket to be centered directly between the other pickets.
Step 5
- Caution: This step involves hitting nails with a hammer in close proximity to your fingers. Work gloves are recommended if you are unfamiliar with using a hammer.
- Hold a wood nail approximately 1 inch from the side of the picket.
- You may place the first nail 1 inch away from either the left or right side of the picket. Each section uses 2 nails so it does not matter which side you choose to work on first.
- Lightly tap on the wood nail with the hammer to begin pushing the nail into the picket. Continue until the nail is fully in the picket.
- Repeat until there are 2 nails inserted in the picket at every cross section.
Caution: This step involves hitting nails with a hammer in close proximity to your fingers. Work gloves are recommended if you are unfamiliar with using a hammer.
Hold a wood nail approximately 1 inch from the side of the picket.
You may place the first nail 1 inch away from either the left or right side of the picket. Each section uses 2 nails so it does not matter which side you choose to work on first.
Lightly tap on the wood nail with the hammer to begin pushing the nail into the picket. Continue until the nail is fully in the picket.
Repeat until there are 2 nails inserted in the picket at every cross section.
This guide only demonstrates how to replace a picket on a wooden fence. For questions regarding staining your fence and finding the right stain, I recommend talking with a worker at a hardware store near you. They can help you find the right product and make sure your new picket matches the rest of your fence.
Cancel: I did not complete this guide.
Author
with 1 other contributor
David Snowden
Member since: 03/02/2021
121 Reputation
1 Guide authored
Badges:
2
Team
University of North Texas, Team S1-G30, Raign Spring 2021
Member of University of North Texas, Team S1-G30, Raign Spring 2021
UNT-RAIGN-S21S1G30
1 Member
1 Guide authored
