Wolf Gourmet Wgtr102S Slide Assist Plunger Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          10 - 15 minutes

Sections

Outer Shell
8 steps
Slide Assist Plunger
3 steps

Flags

BackWolf Gourmet WGTR102S
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Outer Shell

Using a wedge, pry off the rubber pieces on the bottom of each foot of the toaster.

Using a wedge, pry off the rubber pieces on the bottom of each foot of the toaster.

1024

Step 2

Remove the eight 8mm screws on each toaster foot using a Tri-point Y1 screwdriver.

Remove the eight 8mm screws on each toaster foot using a Tri-point Y1 screwdriver.

Step 3

Remove the crumb collector located on the bottom of the toaster.

Remove the crumb collector located on the bottom of the toaster.

Step 4

Remove the three 8mm screws using the Tri-point Y1 screwdriver.

Remove the three 8mm screws using the Tri-point Y1 screwdriver.

Step 5

Remove the two 8mm screws on the bottom of the slide lever using a Tri-point Y1 screwdriver.
Once the screws are removed, detach the black plastic cover on the bottom of the slide lever.

Remove the two 8mm screws on the bottom of the slide lever using a Tri-point Y1 screwdriver.

Once the screws are removed, detach the black plastic cover on the bottom of the slide lever.

Step 6

Remove the final 8mm screw in the slide lever.
The lever can now pull away from the entire unit.

Remove the final 8mm screw in the slide lever.

The lever can now pull away from the entire unit.

Step 7

Remove toaster’s outer shell by lifting straight up.
Slowly remove the outer shell. Disconnect ground wire before fully separating the shell and inner components.

Remove toaster’s outer shell by lifting straight up.

Slowly remove the outer shell. Disconnect ground wire before fully separating the shell and inner components.

Step 8

Disconnect the wire cluster that connects the lights and circuit board by pulling apart the two plastic connectors.
Remove the outer shell from the device.

Disconnect the wire cluster that connects the lights and circuit board by pulling apart the two plastic connectors.

Remove the outer shell from the device.

Step 9

              Slide Assist Plunger

Remove the top panel by bending the tabs on each side straight up.

Remove the top panel by bending the tabs on each side straight up.

Step 10

Remove the two 8mm screws on the bottom of the plunger using a Tri-point Y1 screwdriver.

Remove the two 8mm screws on the bottom of the plunger using a Tri-point Y1 screwdriver.

Step 11

Remove the plunger from the device.

Remove the plunger from the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 2 other contributors

                    Ryan Funchess

Member since: 04/19/2018

697 Reputation

                                      5 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Cal Poly, Team S22-G5, Maness Spring 2018                        

                                                  Member of Cal Poly, Team S22-G5, Maness Spring 2018 



                    CPSU-MANESS-S18S22G5                     


                                            4 Members                     


                                            5 Guides authored

hsernaker - Aug 16, 2021

Where does one get a new plunger for the replacement?

Introduction#

What you need#

Team#

Introduction

What you need

Team