Difficulty

Difficult

Steps

8

Time Required

                          3 hours

Sections

1

  • Touch screen
  • 8 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackWiko Pulp 4G

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Step 1

              Touch screen
  • Remove back cover
  • Remove battery

Remove back cover

Remove battery

1024

Step 2

  • remove the screws marked, attention is covered by a white sticker

remove the screws marked, attention is covered by a white sticker

Step 3

  • using a thin tool separate the middle frame from the body display

using a thin tool separate the middle frame from the body display

Step 4

  • unhook touchscreen connector

unhook touchscreen connector

Step 5

  • Remove 2 screws securing the motherboard
  • Unfasten the connectors
  • remove front and rear cameras

Remove 2 screws securing the motherboard

Unfasten the connectors

remove front and rear cameras

Step 6

  • Unhook cable connection between top and bottom card
  • remove top motherboard

Unhook cable connection between top and bottom card

remove top motherboard

Step 7

  • Heat the phone with a 80-degree plate or with an appropriate dryer
  • With the help of tools or special thin wire begin to separate from the touch glass display
  • Utmost care not to break the display, be sure to insert between the touch screen display instruments and not between glass and touch screen ..
  • There are no flat key is therefore the only attention to the display

Heat the phone with a 80-degree plate or with an appropriate dryer

With the help of tools or special thin wire begin to separate from the touch glass display

Utmost care not to break the display, be sure to insert between the touch screen display instruments and not between glass and touch screen ..

There are no flat key is therefore the only attention to the display

Step 8

  • Clean the display from the sticky residue
  • applying adhesive on the edges and the new touchscreen glass

Clean the display from the sticky residue

applying adhesive on the edges and the new touchscreen glass

To assemble the device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      8 other people completed this guide.                                             


        These translators are helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

Scott Maulsby

Tim

Author

                                      with 2 other contributors 


                    Smilzo

Member since: 11/09/2013

10,473 Reputation

                                      39 Guides authored                  



                       Badges:
                       23







                                                        +20 more badges

Jan Oelbrandt - May 4, 2017

Reply

I replaced a screen on a Acer Wiko Lenny 2 - was very simular to this one. I followed all these steps and it is working BUT the display does not respond as it should. Almost all touches on the outside border of the screen (for example, digit 1 on the left, digit 0 on the right) don’t respond quickly, or don’t respond at all. What could be wrong? If wonder if I didn’t clean the digitizer properly enough…

Smilzo - Jul 26, 2017

Reply

sorry for the delay.

I had some problem with the touch screen too much more intrusive than yours.

I have secured the edges well with scotch because it does not contact me.

But these Chinese touchscreens do not have good quality so I prefer to buy a screen mounted with touchscreen, so I save a lot of time and work is better and working

Roberto Oboe - Aug 3, 2018

Reply

Ciao, come fai a rimuovere i residui di colla dal display, una volta tolto il vetro?

Smilzo - Aug 3, 2018

Reply

Scaldando e con una spatolina ed anche con il puliscicontatti spray